Technical Data; Before Starting The Equipment - EINHELL TC-MC 355 Mode D'emploi D'origine

equipment properly you must also observe the
safety information, the assembly instructions and
the operating instructions to be found in these
operating instructions.
All persons who use and service the equipment
have to be acquainted with these operating
instructions and must be informed about the
equipment's potential hazards. It is also imperati-
ve to observe the accident prevention regulations
in force in your area. The same applies for the
general rules of health and safety at work.
The manufacturer will not be liable for any chan-
ges made to the equipment nor for any damage
resulting from such changes.
Even when the equipment is used as prescribed
it is still impossible to eliminate certain residual
risk factors. The following hazards may arise in
connection with the equipment's construction and
design:
•
Contact with the cutting-off wheel in the unco-
vered cutting zone.
•
Reaching into the cutting-off wheel while it is
running (injuries through cutting).
•
Kick-back of workpieces and parts of work-
pieces.
•
Broken cutting-off wheels.
•
Catapulting of damaged or cutting-off wheels.
•
Damage to hearing if essential ear-muffs are
not used.

4. Technical data

AC motor ..................................220-240V ~ 50Hz
Power P .................................................. 2300 W
Idle speed n .........................................4000 min
0
Cutting-off wheel ......... Ø 355 x Ø 25,4 x 3,2 mm
Base area ...................................... 460 x 260 mm
Swiveling range .................................... -15° - 45°
Max. vise clamping range ....................... 230 mm
Saw width at 90° .............. Ø 100 / 100 x 100 mm
Saw width at 45° .................... Ø 90 / 90 x 90 mm
Weight ......................................................16,7 kg
Anl_TC_MC_355_SPK1.indb 17 Anl_TC_MC_355_SPK1.indb 17
GB
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
L sound pressure level ........................ 93 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ........................ 105 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Important!
The vibration value changes according to the
area of application of the electric equipment and
may exceed the specifi ed value in exceptional
circumstances.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
•
Unpack the metal cutting-off machine and
check it for damage which may have occurred
in transit.
•
Make sure the machine stands securely, i.e.
bolt it to a workbench or solid base.
•
All covers and safety devices have to be pro-
perly fitted before the equipment is switched
on.
•
The spark deflector must be turned out of the
transport position in the direction of the arrow
until a gap forms between the base plate and
the spark deflector. (Fig. 10)
•
The cutting wheel must rotate smoothly.
•
Before you actuate the ON/OFF switch, make
sure that the cutting-off wheel is correctly
fitted and that the machine's moving parts run
smoothly.
- 17 -
16.01.2017 09:09:20 16.01.2017 09:09:20