EINHELL HOME TH-RO 1100 E Mode D'emploi D'origine page 22

material. Use a special vacuum cleaner if you
are handling harmful materials.
•
Secure the extraction port (1) to the routing
shoe (2) using the two countersunk screws
(f).
•
The extraction port can be connected to ext-
ractor units (vacuum cleaners) with a suction
hose.
•
The internal diameter of the suction port is 35
mm. Now fit a suction hose of the appropriate
size to the suction port.
5.2 Safety guard port assembly
(Fig. 3/Item 24)
Fit the safety guard (24) as shown in Fig. 3.
5.3 Parallel stop assembly (Fig. 4/Item 21)
•
Push the guide shafts (a) of the parallel stop
(21) into the holes (b) on the routing shoe (2).
•
Set the parallel stop (21) to the required di-
mension and secure it in place with the wing
screws (3).
5.4 Fitting the compass point (Fig. 5)
•
You can route circular areas using the com-
pass point (13) and the mounting to go with it.
•
Clamp the compass point (13) to the end of
one of the guide rods (a). Push the guide rod
(a) into a hole (b) on the routing shoe (2). Se-
cure the guide rod (a) on the routing shoe (2)
using the securing screws (3).
•
Set the required radius between the compass
point (13) and cutter.
•
Position the compass point (13) in the center
of the circle you wish to route. If necessary
undo the wing screw (c) on the compass
point (13) and extend/shorten the part of the
compass point (13) that points downwards.
5.5 Guide sleeve assembly (Fig. 6-7/Item 20)
•
Secure the guide sleeve (20) to the routing
shoe (2) using the two countersunk screws
(f).
•
The guide sleeve (20) is guided along the
template (c) using the guide ring (b).
•
The workpiece (d) must be larger by the diffe-
rence of "external edge of guide ring" and "ex-
ternal edge of router" (e) to obtain a precise
copy.
Anl_TH_RO_1100_E_SPK1.indb 22 Anl_TH_RO_1100_E_SPK1.indb 22
GB
5.6 Fitting / Removing the cutting tool
(Fig. 8-11)
Important. Pull out the power plug fi rst.
Important. After working with the router,
the cutting tool will remain very hot for a rela-
tively long time.
Important. Cutters are very sharp. Wear
protective gloves at all times when handling
cutting tools.
•
Cutters with a shaft diameter of 6 mm and 8
mm may be fitted to this router. Most cutters
are available in both sizes.
•
You can use cutters made of the following
materials:
- HSS - suitable for cutting softwood
- TCT - suitable for cutting hardwood, particle
board and plastic.
•
Select the appropriate cutting tool for the job
in hand.
•
When using the cutters for the first time: Re-
move the plastic packaging from the cutter
heads.
•
Clean the nut, clamp and shaft of the cutter
before fitting it.
•
Press the spindle lock (12) and allow the
spindle to engage by turning it at the same
time.
•
Undo the clamp nut (10) using the open-
ended spanner (22).
•
If necessary take the cutter you wish to remo-
ve out of the clamp (23).
•
Select the appropriate cutting tool for the job
in hand.
•
Select the appropriate clamp for the cutter
(23).
•
Now fit the clamp (23) and nut (10) into the
cutting spindle.
•
Guide the cutter shaft into the clamp.
•
Press and hold the spindle lock (12).
•
Tighten the clamp nut (10) using the open-
ended spanner (22).
•
The cutter must be inserted at least 20 mm
into the clamp (23).
•
Before you start the electric router, check to
ensure that the cutting tool is secure and runs
smoothly.
Important. Remove the setting and assem-
bly tools before starting the machine
- 22 -
29.06.12 10:46 29.06.12 10:46