Dremel STYLUS 1100-25 Notice Originale page 10

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 18
GENERAL
The Dremel multitool is a high quality precision tool that can
be used to perform detailed and intricate tasks. The wide range
of Dremel accessories and attachments allow you to perform
a large variety of tasks. These include tasks such as sanding,
carving and engraving, cutting, cleaning and polishing.
PICTURE 1
A. Collet Nut
B. Collet
C. On/Off Switch
D. Shaft Lock Button
E. Variable Speed Dial
F. Ventilation Openings
G. Softgrip
H. Charge Indicator Light
I.
Charger
J. Accessory Storage
K. Wrench Storage
CHARGING THE TOOL
The Cordless Rotary Tool is not fully charged. The tool is
equipped with a non-removable battery pack. Be sure to charge
pack prior to initial use.
To charge the tool:
1. Turn tool off.
2. Place tool in the charger.
3. Plug charger into power source.
• Green light ON=charging.
• Solid green OFF=charging completed.
Charger will automatically stop charging the battery when
charging is completed. It is ok to leave tool on charger.
4. Charger will require approximately 5 hours to charge a
completely discharged battery.
IMPORTANT CHARGING NOTES
This tool has a Lithium-Ion battery and docking station offering
the following benefi ts:
1. Lithium-ion battery will hold its charge while in storage for
up to 2 years so it's always ready when you need it.
2. You can place the tool on the charger and recharge it at any
time without reducing the original factory charge capacity.
3. The charger was designed to use as a place to store your
tool while you are working on your projects. Simply place
the tool in the charger when you're not using it on your
project, and it will continually recharge the battery so it will
run longer.
4. The charger was designed to fast charge the battery only
when the battery temperature is between 4°C and 41°C.
5. If battery does not charge properly:
a. Check to see if tool is properly placed in charger.
b. Check for voltage at outlet by plugging in some other
electrical device.
c. Check to see if outlet is connected to a light switch
which turns power "off" when lights are turned off.
d. Check battery pack terminals for dirt. Clean with cotton
swab and alcohol if necessary.
NOTE: Use of chargers not sold by Dremel may void the
warranty.
The Dremel accessories available for the multitool come
with various shank sizes. Four size collets are available to
accommodate the different shank sizes. Collet sizes are
identifi ed by the rings on the back of the collet.
PICTURE 2
L. 0.8 mm Collet with one ring (483)
M. 1.6 mm Collet with two rings (482)
N. 2.4 mm Collet with three rings (481)
O. 3.2 mm Collet without ring (480)
NOTE: Some multitool kits may not include all four collet sizes.
Collets are available separately.
Always use the collet that matches the shank size of the
accessory you plan to use. Do not force a larger diameter shank
into a smaller collet.
CHANGING COLLETS
PICTURE 3
P. Shaft Lock Button
Q. Collet Wrench
R. To tighten
S. To loosen
T. Collet Nut
1. Slide the shaft lock button forward, hold down and rotate
the shaft by hand until it engages the shaft lock. Do not
engage the shaft lock button while multitool is running.
2. With the shaft lock button engaged, loosen and remove the
collet nut. Use the collet wrench if necessary.
3. Remove the collet by pulling it free from the shaft.
4. Install the appropriate size collet fully into the shaft and
reinstall the collet nut fi nger tight. Do not fully tighten the
nut when there is no bit or accessory installed.
CHANGING ACCESSORIES
PICTURE 3/4
P. Shaft Lock Button
1. Slide the shaft lock button forward, hold down and rotate
the shaft by hand until it engages the shaft lock.
2. With the shaft lock button engaged, loosen (do not remove)
the collet nut. Use the collet wrench if necessary.
3. Insert the bit or accessory shank fully into the collet.
4. With the shaft lock button engaged, fi nger tighten the collet nut
until the bit or accessory shank is gripped by the collet. Use
the collet wrench to secure the bit or accessory in the collet.
NOTE: Be sure to read the instructions supplied with your Dremel
accessory for further information on its use.
Use only Dremel tested, high performance accessories.
10
COLLETS

Publicité

Table des Matières
loading

Table des Matières