OPERATING INSTRUCTIONS cont.
Emptying Dust Cup & Cleaning
Dust Cup Filter
Warning:
Always unplug from electrical
outlet before opening the Dust Cup
(container).
1. To open the Dust Cup (container), push
button and pull out the Dust Cup
(container).
2. Pull out the Dust Cup Filter.
3. Empty the dust from the Dust Cup Filter.
4. Rinse the Dust Cup Filter in cold water,
and then wait until it dries completely
before replacing it into the Dust Cup
(container).
5. Place the Dust Cup Filter carefully into the
Dust Cup (container).
6. Attach the Dust Cup (container) to the
Hand Vacuum.
CAUTION
:
The suction hole must be open,
free of any obstructions at all times.
Otherwise, the motor will overheat and could
get damaged.
Air Driven Turbo Brush
Using The Unit With Air Driven
Turbo Brush
The efficiency of your air driven turbo brush
depends on the bristle brush rotating at high
speed. Strong air suction is needed to
accomplish this. In order to ensure that
maximum air suction is maintained, please
read the following instructions:
1. Empty the dust cup frequently.
2. Always shake out the dust cup filter when
emptying the dust cup container.
3. Ensure that the rotating brush is kept free
of hair and string which may accumulate
and decrease brush performance.
4. Keep Air Driven Turbo Brush turbine free of
dirt and foreign matter. (See illustration
below for cleaning instructions.)
Using The Unit With Air Driven
Turbo Brush
1. Slide the narrow end of one of the
extension tubes into the wide end of
the other extension tube.
2. Slide the narrow end of the extension
tube into the air driven turbo brush.
3. Slide the wide end of the assembled
extension tube onto the round end of the
deluxe hose with suction control.
4. Slide the round side of the
deluxe hose with suction control into
the suction hole of the vacuum unit.
5. Attach the shoulder strap to the vacuum
and hang it from your shoulder.
6. You can now proceed to vacuum your
carpet or hard floor.
Cleaning Air Driven Turbo Brush
Locking Latch
Turbine
From time to time, the turbine of your turbo
brush will require cleaning. To do this:
1. Remove the turbo brush from the hose
or extension tube.
2. Slide locking latch forward then tilt the
top housing of the brush upwards. The
top housing is hinged and will tilt up
approximately 45° only.
3. There may be some dust, lint, hair, etc
on the turbine wheel. Remove as much
of this as possible.
4. You may also use the unit's hose with
crevice tool attached and use the vacuum
to remove any additional debris from the
turbine.
5. Ensure that the turbine wheel moves
freely by rotating it with your finger. If the
turbine does not rotate, call EURO-PRO
Customer Service for help.
6. Once clean, close the top cover of the
turbo brush and slide the locking latch
toward the rear of the brush to lock.
4
CHANGEMENT DU FILTRE HEPA DU DÉBIT D'AIR
Le filtre HEPA du débit d'air doit être
changé une ou deux fois par année,
selon l'usage.
1. Pour changer la cartouche du filtre
HEPA, agrippez l'aspirateur par sa
poignée et, à l'aide des languettes
sur la cartouche du filtre, tirez le filtre
vers le bas.
2. Une cuiller ou autre « levier » pourrait
être requis pour retirer la cartouche
de l'appareil. La cartouche est
conçue pour s'insérer étroitement
dans l'aspirateur afin de maximiser la
filtration et réduire les fuites d'air.
3. Pour installer une nouvelle cartouche,
insérez son extrémité mince dans
l'aspirateur en vous assurant que la
languette fait face vers l'arrière.
4. Glissez la cartouche dans l'appareil
Tilt
jusqu'à ce qu'elle « clique » en place.
Upwards
THERMOSTAT DU MOTEUR
Important
: L
e moteur est muni d'un thermostat de protection. Si, pour quelque raison,
l'aspirateur venait à surchauffer, le thermostat arrêtera immédiatement l'appareil. Si cela se
produit : débranchez l'appareil de la prise murale ou arrêtez-le à l'aide du commutateur.
Laissez refroidir l'appareil. Pour le remettre en marche, branchez l'appareil de nouveau
dans la prise murale ou remettez-le en marche à l'aide du commutateur.
INSTRUCTIONS D 'OPERATION
13
Tirez