aquabrass TURBO TOTEM T12000 Guide D'installation
Masquer les pouces
Voir aussi pour TURBO TOTEM T12000:
- Guide d'installation (14 pages) ,
- Guide d'installation (13 pages)
Manuels Connexes pour aquabrass TURBO TOTEM T12000
Sommaire des Matières pour aquabrass TURBO TOTEM T12000
- Page 1 TURBO TOTEM T12000 Installation Guide Guide d’installation TURBO TOTEM #T-12000 3/4” - 1/2” thermostatic valve Valve thermostatique 3/4” - 1/2” Last revision : 24/07/2019 aquabrass.com...
- Page 2 TURBO TOTEM T12000 Service Parts / Schéma des pièces Pre-calibrated at 38°C DO NOT ROTATE Ajusté à l’usine Code English Français ABSP12095 Check valve COLD (with a line) Valve d’arrêt FROID (avec une ligne) ABSP12094 Check valve HOT (with a cross) Valve d’arrêt CHAUD (avec une croix)
-
Page 3: General Dimensions / Dimensions Générales
TURBO TOTEM T12000 General Dimensions / Dimensions générales TURBO TOTEM T-12000 [80.00] Min. 3 1/4” 3 1/8” Max 3 3/4” Finished wall 3/4” NPT-1/2” FPT (Outlet) 3/4” NPT -1/2” FPT (Sortie) [55.00] 2 3/16” [125.00] 4 15/16” 3/4” NPT 1/2” FPT Inlet (HOT) 3/4”... -
Page 4: Préparation Du Mur
TURBO TOTEM T12000 Installation Wall Setup Préparation du mur Wood screw/Vis à bois (not supplied / non fournies) Determine the valve location in the wall. For an optimal installation, position the valve on a plywood backing attached the adjacent 2x4 studs. - Page 5 TURBO TOTEM T12000 Connecting the water Raccordement de l’eau Ensure all piping is free from debris and dirt to prevent blockage in the mixer. The hot water inlet should always feed the check valve with a cross marking (normally on the left), the cold water inlet feeds the check valve with a line marking (normally on the right).
- Page 6 TURBO TOTEM T12000 Wall oppening Ouverture du mur For an easy maintenance of the valve components [100.00] after installation, the valve opening should be of 3” x 3 3 7/8” 9/16” on the finished wall. This will facilitate the access for cartridge replacements and also for all recommended maintenances.
- Page 7 TURBO TOTEM T12000 Optional configuration / Configurations optionelles #1438 #3008 #1436 #1206 #61934 #T-12000 Independent diverter 61934 Déviateur indépendant 61934 Turbo totem T12000 Valve d’arrêt 1/2’’ 1206 3/4” - 1/2” Thermostatic valve 1/2’’ shut-off valve 1206 Valve thermostatique 3/4” - 1/2”...
- Page 8 TURBO TOTEM T12000 To clean your Aquabrass faucet or accessories, wash with a wet nonabrasive soapy cloth. Then wipe dry with a soft towel or cloth. We recommend this be done on a regular basis. DO NOT USE ANY ABRASIVE, CHEMICAL OR CORROSIVE, POWDER OR ANY OTHER STRONG CLEANERS INCLUDING DETERGENTS, WIN- DOW CLEANERS AND DISINFECTANTS ON YOUR Aquabrass PRODUCT as they will destroy the finish and therefore VOID THE WARRANTY.
-
Page 9: Garantie Limitée À Vie
- Aquabrass polished chrome and brushed nickel finishes are warranted for the life of the product to the original purchaser. All other finishes will be warranted for five years (Satin Nickel Natural [#210] is designed to develop a patina over time). Raw Brass (#400) is a living finish for which there is no warranty Normal wear and tear is not covered by this warranty.