Wiring & Installation - Kicker KM67S Manuel D'utilisation

Models:
Authorized KICKER Dealer:
Purchase Date:
Speaker Serial Number:
The Kicker KMS67 high-effi ciency component system is specially designed for "Livin' Loud" out in
the harsh marine environment, and is made using advanced materials and construction techniques,
maintaining optimal performance for years to come. The KMS67 features a pair of 6.75 inch mid-bass
woofers and 1.7 inch horn-loaded compression drivers. Combine the KMS67 and KM67S for a 6-driver
system.
SPECIFICATIONS
Model:
Woofer [in, mm]
Horn Loaded Compression Driver [in,mm]
Horn Exit
Dome Material
Rated Impedance [Ω]
Peak Power Handling [ Watts]
Continuous Power Handling [Watts RMS]
Sensitivity [1W, 1m]
Frequency Response [Hz]
Woofer Mounting Hole Diameter [in, mm]
Woofer Bottom Mount Depth [in, mm]
Horn Mounting Hole Diameter [in,mm]
Horn Mounting Depth [in,mm]
High Pass [dB], at Frequency [Hz]
Low Pass [dB], at Frequency [Hz]
High Frequency Output Attenuation [dB]
*- Available through KICKER warranty
WIRING & INSTALLATION
Wire and install the KMS67 drivers and horns to your speaker
cans as per the manufacturer's instructions. For optimal
performance, consider loosely fi lling 50%-100% of the can
with poly-fi l.
Wire the cans in parallel as illustrated at the top of Page 3.
If you've added an additional mid to each channel with the
KM67S, please reference the diagram at the bottom of page
3.
To get the best performance with minimal distortion out of your
KM system, use a high-pass fi lter (or crossover); 80–100Hz is
a good starting point.
2
2014 KMS Rev E.indd 2-3 2014 KMS Rev E.indd 2-3
KMS Component System
Owner's Manual
KM67S | KMS67
KMS67 KM67S*
6-3/4, 165 6-3/4, 165
1.7, 43 N/A
Tractrix 60°-V x 90°-H N/A
Titanium N/A
4 4
400 200
200 100
94.5dB 1 mid, 99.5dB 2 mids 90.5dB
50–22k 50-1700
5-11/16, 144 5-11/16, 144
3-7/8, 99 3-7/8, 99
5-11/16, 144 N/A
7-3/16, 183 N/A
18, 1700 N/A
12, 1700 12, 1700
0, +6 N/A
+
-
+
Horn Can
CROSSOVER
The KMS67 uses a built-in crossover for both the mid and horn. To adjust the output level, use the jumper
on the back of the horn-loaded compression driver by pushing down on the terminal, inserting the wire
and then releasing the terminal to secure it. For example, when using the KMS67 with extra mids provided
in the KM67S, move the jumper wire to +6 dB.
Horn-loaded compression driver
0 dB gives a fl at frequency
response and is the recommended
confi guration for use with one mid.
+6 dB gives a fl at frequency
response and is the recommended
confi guration for use with two mids.
Mid Can
Terminal
-
Note: Kicker Marine speakers meet or exceed industry standards for environmental humidity and corrosion, and for
material degradation due to UV exposure.
Terminal Terminal
+
-
From Amplifi er
Horn Can
Terminal Terminal
+
From Amplifi er
Mid Can
Jumper Wire
Mid Can
-
3
8/29/2013 2:07:22 PM 8/29/2013 2:07:22 PM