Instructions For Use; Filling The Boiler Tank Before Use; Switching On; Operation - ARIETE Multi Vapori MV7.30 Instructions D'emploi

EN

Filling the boiler tank before use

• Remove the cap (R) from the tank (P) and fill it with water, taking care not to exceed the "
• The tank (P) can be removed by pulling it out by the handle and it can be filled with mains water, even directly from the tap.
• Then refit the tank (P), taking care that the bottom valves meet up with the pins in the seat of the appliance. Press the tank
down until it is completely inserted and make sure it has been correctly fitted (
• Press in the cap (R).
• Fit the required tool (see the "
stains), insert the detergent following the instructions in the paragraph "USING WITH DETERGENT".
IMPORTANT: Never use the appliance without water in the tank as this could damage the pump.
IMPORTANT: The Tank has a safety cap (S) on the back, which can be seen once the tank has been taken
out. The safety cap serves as a valve which, in the event of malfunctioning caused by excess pressure in
the boiler tank, will open to allow steam to come out. In this case, the appliance will no longer be able to
dispense steam.

Switching on

• Plug the appliance into a mains socket and press the on/off switch (N); the red light (L) will switch on (
• After a few minutes, the green light (M) will switch on to show that the steam is ready, meaning that the tank is pressurised
and that the appliance is ready to dispense steam.

Operation

• The boiler tank is supplied automatically via a pump that switches on for a few seconds every time the appliance is filled,
generating normal operation noise (vibration). Immediately after the pump has switched on, there may be a drop in steam
dispensing but, after a few seconds, steam dispensing will return to normal.
• The steam ready light (M) switches on and off during use, which shows that the boiler tank is operating.
• To prevent the steam from being dispensed accidentally, the lock cursor (C) must be moved from the left to the right
to release the steam function, move the cursor (C) from right to left( ) (
• To dispense steam, press the button (B) on the gun (D).
• When using for the first time, it is a good idea to spray the steam jet into a container to get rid of any water residues that
might be inside the tube (any water coming out is because of the condensed steam inside the tube). This action needs to
be repeated even after a few minutes of appliance inactivity. In any case, when the gun begins to dispense steam, always
point the jet downwards to the ground.
IMPORTANT: When the appliance is not used, always block the steam button (B) using the relevant cursor
(C).

Steam jet regulation

• Use the dial (O), to regulate the amount of steam dispensed, from a minimum to a maximum, based on cleaning needs
and on the type of surface or upholstery being cleaned.
• Reduce the pressure for delicate surfaces and fabrics.

Switching off the appliance

• Do not use the dial (O) to stop dispensing steam; release the dispenser button (B).
• The appliance has a pressure gauge (G) to show the pressure of the steam inside the boiler tank.
• At the end of use, switch off the appliance, pressing the switch (N), remove the plug and rewind the power cord by holding
down the rewind button (H) on the appliance. The power cord will rewind inside the container.
IMPORTANT: When rewinding the cord, guide it with one hand to avoid any risk of injury. Always take great
care if children or pets are in the vicinity.
• Proceed to clean the attachments, the water tank (P) and the tank, as described in the paragraph "
MAINTENANCE".
• Wind the hose around the body of the appliance (I) and fit the gun (D) over the handle (F), after placing the cursor (C) in
the lock position.

INSTRUCTIONS FOR USE

ATTACHMENTS" paragraph) to the gun (D) and only if strictly necessary (e.g. stubborn
- 14 -
MAX" level on the tank (
).
2
).
4
).
1
).
3
( );
CLEANING AND