Safety Instructions For Box Column Drills - Woodstar 3906812952 Traduction De La Notice Originale

to ensure the proper operation of the power tool.
- Damaged safety equipment and parts must be re-
paired properly or replaced by an authorised spe-
cialist workshop unless otherwise indicated in the
instructions.
- Damaged switches must be replaced at a customer
service workshop.
- Do not use power tools if the switch cannot be tur-
ned on and off.
• CAUTION!
- The use of other bits and other accessories can re-
sult in a risk of personal injury.
• Have your power tool be repaired by a qualified
electrician
- This power tool complies with the relevant safety re-
gulations. Repairs may only be performed by a qua-
lified electrician, using original spare parts; otherwi-
se accidents involving the user may result.
Service:
• Have your power tool repaired only by qualified
specialists and only with original spare parts.
This will ensure that the power tool remains safe.

Safety Instructions for Box Column Drills

• Never make the warning labels on the power tool
illegible.
• Attach the power tool to a solid, flat and horizon-
tal surface. If the power tool can slip or wobble, the
bit may not be guided smoothly and safely.
• Keep the work area clean except for the work-
piece to be machined. Sharp-edged drilling chips
and objects can cause injury. Material mixtures are
particularly dangerous. Light metal dust can burn or
explode.
• Set the correct speed before starting work. The
speed must be appropriate for the drill diameter
and the material to be drilled. At an incorrectly set
speed the bit may get jammed in the workpiece.
• Only when the device is turned on should the bit
be moved against the work piece. Otherwise there
is a danger that the bit will get jammed in the work-
piece and the workpiece will rotate with the bit. This
can lead to injuries.
• Do not put your hands in the area of the drill
while the power tool is running. Upon contact with
the bit is a risk of injury.
• Never remove drilling chips from the drilling
area while the power tool is running.Always put
the drive mechanism in the standby position first and
then turn on the power tool.
• Do not remove accumulated drill chips with your
bare hands. There is a risk of injury due to hot and
sharp metal shavings in particular.
• Break up long drilling chips by interrupting the
drilling operation with a short backward rotation of
the rotary wheel. Long drilling chips may cause injury.
• Keep handles dry, clean and free from oil and
grease. Greasy, oily handles are slippery and lead
to loss of control.
22 І 44
• Use clamps to hold the workpiece in place. Do
not work on any workpieces that are too small
for clamping. If you hold the workpiece by hand,
you cannot hold it sufficiently tightly against rotation
and may hurt yourself.
• Switch the power tool off immediately if the bit
jams. The bit jams when:
- the power tool is overloaded or
- the workpiece to be machined is jammed.
• Do not touch the bit after working before it has
cooled down. The bit is very hot during use.
• Inspect the cable regularly and have a damaged
cable repaired only by an authorised customer
service centre. Replace damaged extension
cables. This will ensure that the power tool remains
safe.
• Store unused power tools in a safe place. The
storage place should be dry and lockable. This
prevents the power tool from being damaged as a
result of being stored or operated by inexperienced
people.
• Never leave the tool before it has come to a com-
plete standstill. Afterrunning bits can cause injury.
• Do not use the power tool with a damaged cable.
Do not touch the damaged cable and pull the
mains plug if the cable is damaged while wor-
king. Damaged cables increase the risk of electric
shock.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and you environment from acci-
dents using suitable precautionary measures!
• Do not look directly into the laser beam with unpro-
tected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting sur-
faces and persons or animals. Even a laser beam
with a low output can cause damage to the eyes.
• Caution - methods other than those specified here
can result in dangerous radiation exposure.
• Never open the laser module. Unexpected exposure
to the beam can occur.
• If the mitre saw is not used for an extended period
of time, the batteries should be removed.
• The laser may not be replaced with a different type
of laser.
• Repairs of the laser may only be carried out by the
laser manufacturer or an authorised representative.