Manufacturer's Warranty - Inokey system digibell Instructions D'utilisation

all existing remote controls again. The same procedure of era-
sing the entire remote control base and pairing the existing
remote controls again must be followed also in case a remote
control is lost and there is a risk that the finder of the remote
control might use it for unauthorised entering.
Erasing the remote control base:
If the remote control base needs to be erased, this must be
done by following the next procedure:
•
Unscrew the electric safety bolt of the door and pull out the
relay unit from the door profile.
•
Press the button on the relay unit for 30s.
•
After 30s the device emits 5 beeps, after which the remote
control base is erased.
Note:
After the remote control base is erased, all existing remote
controls must be paired again.
4. DOORBELL
The device is equipped with a wireless doorbell. The doorbell
is powered by 220V alternating voltage. On the back side the
doorbell has a plug for standard EU sockets.
The maximum range of the doorbell is 60m in outdoor areas.
In indoor areas the range may be hindered by partitions, espe-
cially if they are made of reinforced concrete.
The doorbell can be connected to a 220V socket anywhere in
the house, when choosing the location of the doorbell you
need to consider the transmitter range.
Doorbell triggering:
The doorbell can be triggered in two ways.
•
The first way to trigger the doorbell is with the use of the
receiver unit key, which is installed in the outer side of the
door. The surface of the receiving unit is lit, so it is visible at
night, as well. The doorbell key is capacitive and it detects
a finger touching the plastic surface with the doorbell icon.
By pressing the doorbell icon gently you trigger the trans-
mitter and the doorbell rings.
•
The second way to trigger the doorbell is with the use of
a remote control. By pressing the key B or C on the remote
control for 1s you trigger the transmitter and the doorbell
rings.
5. MAINTENANCE AND CLEANING OF THE DEVICE
The device does not require maintenance. Should the device
need cleaning, use a dry or slightly damp soft cloth. Do not
use aggressive detergents, solvents, lye or acids for cleaning.
Use of aggressive cleaning agents may damage the surface of
the device; in this case complaints are invalid.

6. MANUFACTURER'S WARRANTY

Warranty conditions:
The warranty period is 24 months from the day of hand on
of the product to the final customer. With this statement, the
manufacturer of the product, NAVKOM d.o.o., guarantees that
in the warranty period the Inokey digibell (hereinafter: the
product) will operate faultlessly and that the materials it is
made of are faultless and undamaged. If the customer finds
a fault in the functioning of the product, they can enforce the
rights under the warranty on the seller or the manufacturer,
who shall issue a claim receipt. The manufacturer undertakes
that in the event of a justified complaint they shall eliminate
the malfunction no later than 45 days after the day of compla-
int. If the malfunction is impossible to repair, the customer will
receive a new product from the seller or the manufacturer no
later than 45 days after the day of complaint.
Notes concerning the warranty enforcement:
The customer assumes all risks and expenses incurred during
the transport of the product to the licensed seller or the licen-
sed service.
The warranty is only valid if the warranty certificate is comple-
tely filled in by Navkom d.o.o. or a licensed seller of the pro-
duct or if the circumstances of the purchase are satisfactorily
evidenced from other documents. Therefore, please ensure
that your name, the name of the seller, the serial number
of the product, the year, month and day of the purchase are
written in full in the original pro forma invoice or invoice; or
see to it that your purchase receipt showing the name of the
seller, the date of the purchase and type of product is attached
to the original warranty certificate. Navkom d.o.o. reserves the
right to refuse to provide repairs free of charge where the sub-
mitted warranty certificate is not completely filled in and the
above mentioned document (invoice, bill) is not enclosed, or
when the data on the warranty certificate are not completed
or are illegible. Keep the warranty certificate in a safe place
because we cannot issue a duplicate.
Warranty extension:
In the case that the customer enforced the warranty and the
ENG
5