LEGRAND 4 305 72 Mode D'emploi page 7

1. To ensure a normal operation, the remote control should not be dropped or damaged in any way .It should also be kept dry and away from
all heat sources.
2. Battery (CR 2025) replacement is necessary when the remote controller acts inconsistently or stops operating the LCD display.
Choose the input source
If you hope to enjoy the picture from the external input source, before to select the source ,you need to connect the devices,otherwise,when
you select the source ,the none or no signal will appears on the screen, Press source(input) button on the monitor or remote control,the menu
appears on the screen ,then press source to select the monitor item, and press" +/- (>)" to ensure it
On the screen:
"Source" : Select from menu
"Source" : Choose source
"+" or "-" : Confirm source
OSD setup
PICTURE
SOUND
SYSTEM
GEOMETRY
PIP
ADVANCE
Brightness: Adjusts the brightness of the picture.
Contrast : Adjusts the difference between the light and dark areas of the picture.
Color temp: Press ">" button.
Change the color intensity of the temperature Selected (Normal.warm.cool.s-RGB. user)
Scale: Normal.center.
Auto: (auto-adjust) press "> " button.
Performs automatic configuration of the Phase, Clock, vertical and horizontal position.
Picture mode: Press or v button to select picture mode, then press the < or > buttons to select
^
the correct color system, in general, you can see it as "USER".
Press < or >button to select "standard,dynamic. Soft and user".
Equalizer: The five-band graphic equalizer lets you adjust the audio frequency settings.
You can select one of the five-band Equalizer. Presets or create your own personal preset.
Balance: Adjusts how much audio is sent to the left and right(-50 to +50).
The intermediate value is 0,when indication value of balance increases toward +50, sound of the
right and left speaker becomes stronger and weaker, respectively, when indication value of balance
decrease toward -50 sound of the right and left speaker becomes weaker and stronger.
Sound Mode: Provides special processing through your speakers (depending on the setting you
chose as your Sound Type). The available audio modes are: Standard. User. movie. music.
AVC: ON OFF
SURROUND: The surround sond feature expands the audio listening field wider and deeper to
create exceptional sound quality from the monitor's speakers
Language: Lets you select your preferred language for the menus: English. Chinese. German.
French. Spanish. Portuguese. Russian. Italian
OSD H-POSITION: H-position moves the OSD position left (0-50) or press the "> " button.
H-position moves the OSD position right (51-100).
OSD V-POSITION: Adjust the OSD image vertically by pressing the "< or > " button.
V-position moves the OSD position up or down. 0-100.
OSD DURATION: 0-50 - OSD HALFTONE: 0-100
Sleep-timer: Lets you set the monitor to turn off after a given amount of time
(off .15min.30min.45min.60min)
MEM-RECALL: Press > key will be reset to the factory defaults.
H-POSITION: Moves image horizontally on screen either left (<) or right (>).
V-POSITION: Moves images vertically on screen either up (<) or down (>).
CLOCK: If the clock setting of your image is not fine-tuned, you may observe periodic vertical
bars of video noise on your image. These bars of noise are usually adjusted out when an Auto
Configuration is performed. If the bars of noise are still present, this setting can be adjust manually.
PHASE: If the phase of your monitor is not fine-tuned, you may observe unstable horizontal
MULTI WINDOW: OFF.PIP. POP
The default value is off, Lets you select your window for the picture: PIP . POP
Press < or > for desired adjust parameter option until satisfactory value is achieved.
When VGA signals are received automatic mode is used for parameter adjustment.
Hsize: Horizontal size of picture can be adjust in this item.
HSTART: Horizontal position of picture can be adjust in this item.
Vsize: Vertical size of picture can be adjusted in this item.
VSTART: Vertical position of picture can be adjust in this item.
On the remote control:
"Input" : Select from menu
" ^ " or "v" : Choose source
"<" or ">" : Confirm source
Remark