ENGLISH
A typical setup when used as a DJ LED light modulator:
Just "daisy chain" the DMX in/outputs of all connected LED PAR projectors with the DMX-output of the
LEDCON-02 remote using a good quality balanced cable. You can connect up to 120 units! If you use
minimum 8 projectors, you can put the LEDCON-02 in 8channel mode.
Important! Don't forget to run the "auto address" function, this will give all connected units their own
address. (refer to the chapter "ADDRESSING") DIP switches 0 to 9 on the LED PAR must be OFF!
ADDRESSING
Each time you build a different installation with the LEDCON-02, you should run this function. The LEDCON-
02 will distribute new addresses to the connected projectors. There are two ways to distribute the addresses:
1. FULL AUTOMATIC ADDRESS DISTRIBUTION :
The LEDCON-02 distributes the addresses automatically to all the connected LED projectors. The first
unit in the chain receives address 1, the next will have address 2, ... The address distribution depends
on the channel mode and the number of connected LED projectors. Some examples:
Set to 4 channel mode with 20 projectors addressing will be: 1234 – 1234 – 1234 – 1234 - 1234
Set to 8 channel mode with 20 projectors addressing will be: 12345678 – 12345678 - 1234
A. First determine if you will put the LEDCON-02 in 4 or 8 channel mode (see switch n°12)
B. Connect all projectors to the LEDCON-02 and switch the complete setup on.
C. Press the "blackout" button (see n°8) for about 5seconds: until the red "blackout LED" starts blinking.
D. You will see notice that the first LED projector in the chain is lit.
E. Press the "sound to chase" button (see n°6) to select all projectors: all projectors are lit!
F. Press the "random chase" button (see n°1)
G. Press the "blackout" button again for about 5 seconds, until the "blackout" LED stops blinking.
H. Done!
2. MANUAL ADDRESS DISTRIBUTION :
The user can determine the order of succession of the LED projectors: you have full impact on the
configuration but it takes more time to set up an installation with many projectors.
A. First determine if you will put the LEDCON-02 in 4 or 8 channel mode (see switch n°12)
B. Connect all projectors to the LEDCON-02 and switch the complete setup on.
C. Press the "blackout" button (see n°8) for about 5seconds: until the red "blackout LED" starts blinking.
D. You will see notice that the first LED projector in the chain is lit. Now you can determine the address
of this projector by pressing the corresponding color/chase button (see n°1):
Press button "chase1" the current LED projector receives address 1
o
Press button "chase2" the current LED projector receives address 2
o
Press button "chase3" the current LED projector receives address 3
o
Press button "chase4" the current LED projector receives address 4
o
Press button "chase5" the current LED projector receives address 5
o
Press button "chase6" the current LED projector receives address 6
o
JB SYSTEMS
®
OPERATION MANUAL
5/30
LEDCON-02
ENGLISH
Press button "chase7" the current LED projector receives address 7
o
Press button "chase8" the current LED projector receives address 8
o
E. Press the "full on" button (see n°7) to select the next projector and return to "D" until all projectors
received an address. If you want to select the previous projector, simply press the "sound to chase"
button (see n°6). Several projectors can be put on the same address.
F. When all projectors received an address, press the "blackout" button again for about 5 seconds, until
the "blackout" LED stops blinking.
G. Done!
SPECIFICATIONS
Power Input:
DC 9V 300mA minimum.
AC 240V, 50Hz 9Vdc / 300mA (or more)
AC/DC Power adapter:
DMX output:
3pin XLR
Audio input:
None, internal microphone
Size:
21,0 x 14,0 x 4,6cm
Weight:
930 grams
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
JB SYSTEMS
®
OPERATION MANUAL
6/30
LEDCON-02