Safety Features - REHOBOT 363-1 Mode D'emploi

GB
Thank you for the confidence you have shown in us by
choosing a REHOBOT product. REHOBOT stands for pro-
ducts of high quality and we hope that you will have many
years of satisfactory use from this product.
To avoid operating difficulties we recommend that you read
through these instructions before using the product.
Technical description (Fig. 1)
363-1
Hydraulic side cutter equipped with built-in relief valve,
which allows tool to be connected to a pump with a higher
working pressure than the maximum working pressure of
the tool.
Max. working pressure: 70 MPa (10150 psi)
Max. cutting force: 140 kN (14 tonnes)
Max. opening: 26 mm (1.02) in)
Weight: 8.5 kg
369
Hydraulic side cutter.
Max. working pressure: 70 MPa (10150 psi)
Max. cutting force: 140 kN (14 tonnes)
Max. opening: 26 mm (1.02) in)
Weight: 6.7 kg (14.77 lbs)
Warning!
Tool 369 is designed for a maximum working
pressure of 70 MPa (10150 psi). Never connect the tool to
a hydraulic pump without first checking that the working
pressure of the pump does not exceed 70 MPa (10150
psi).
HCE25V
Hydraulic end cutter equipped with built-in relief valve,
which allows tool to be connected to a pump with a higher
working pressure than the maximum working pressure of
the tool.
Max. working pressure: 70 MPa (10150 psi)
Max. cutting force: 90 kN (9 tonnes)
Max. opening: 25 mm (0.98) in)
Weight: 8.2 kg (18.08 lbs)
HCE25
Hydraulic end cutter.
Max. working pressure: 70 MPa (10150 psi)
Max. cutting force: 90 kN (9 tonnes)
Max. opening: 25 mm (0.98) in)
Weight: 7.0 kg (15.44 lbs)
REHOBOT Hydraulics AB
(18.74 lbs)
Skjulstagatan 11 A, 632 29 Eskilstuna, SWEDEN P.O. Box 1107 631 80 Eskilstuna
T. +46 (0)16 - 16 82 00 F. +46 (0)16 - 13 93 16 info@rehobot.se www.rehobot.se
Warning!
Tool HCE25 is designed for a maximum working
pressure of 70 MPa (10150 psi). Never connect the tool to a
hydraulic pump without first checking that the working pres-
sure of the pump does not exceed 70 MPa (10150 psi).
Connection to pump
363-1 / HCE25V
The tool is equipped with two 0.5 m long hoses and quick
couplings to allow connection to a pump. The hose (marked
"PRESSURE") that is connected to the pump pressure outlet
is fitted with a male coupling. The return hose that is con-
nected to the pump return connection is fitted with a female
coupling.
The male and female couplings can only be connected when
the hoses are depressurised.
369 / HCE25
The tool is equipped with quick couplings (male couplings)
to allow connection to a hose and pump.
Male and female couplings can only be connected when the
tool is depressurised.
Operation
363-1 / HCE25V
The tool is operated using a control lever. Press the lever
in to cut. Release the lever and the shears open to their
original position.
369 / HCE25
The tool is operated using the control device on the connec-
ted pump.

Safety features

363-1 / HCE25V
The tool is equipped with a built-in relief valve.
Safety
• Always wear suitable personal safety equipment, overall,
helmet, visor or safety goggles, gloves, etc.
• Consider the risk of spark formation if you cut through
electric cables. Always start work by making sure that the
object to be cut is not connected to an electrical supply.
• Take great care when cutting springs or spring mountings.
These are often under tension and may cause injury when
they are freed.