Nitto Kohki delvo DLV02SL-CKE Notice D'utilisation page 4

and may invalidate your warranty.
23. Do not allow the following chemicals to come into
contact with the tool housing, as damage will
result. For example, trichloroethylene acetone,
benzene, thinner,
chemicals.
2.OPERATION CAUTIONS
CAUTION
1. Use at the voltage, which is indicated on the rating
plate. If used at a higher voltage than indicated, it
may cause damage and accident.
2. When the tool does not work properly, or you hear
abnormal sounds
immediately and request the repair work to be done
by an authorized service facility. If you keep on
using the tool, it may cause injury.
3. Install only bits or accessories in accordance with
the operation manual.
4. Grounding is necessary to be assured, especially for
the bit earth type.
5. Whenever setting the torque, switch off the tools
and components.
6. Whenever changing the bit, ensure the changeover
switch is in the "O" (Off) position and the tool is
unplugged.
7. If the rest interval is shorter than three seconds,
the heat of the motor may increase. However, it
differs from the kind of screw or from the fastening
torque.
8. Do not adjust the torque setting higher than the
number of the torque scale mentioned below.
The number on the torque scale does not indicate
the torque value of the screwdriver. The torque
varies according to the type, size, and material of
3. S
PECIFICATION
Standard
MODEL
ESD
[Nm]
Torque
[Lb-in]
Free Speed [min ]
-1
Input Voltage
Power Consumption [W]
Duty Cycle [sec]
Machine Screw
Screw Size
Inch thread
[mm]
Tapping Screw
Bit Type
Mass
Noise emission
[EN60745-1]
Vibration level [EN60745-1]
Standard Accessories
ketone, or other
during usage, switch
DLV02SL-CKE
DLV02SL-BKE
0.03
0.27 to 1.8
1.0
#2 or less
1.0
*L
pA
*L
WA
Bit No.0x3.8x50: 1Pic
Bit No.1x3.8x50: 1Pic
Connection Cable(2.4 m / 7.87 ft): 1Pic
screws and work. Therefore, use the following
diagram as references to obtain an appropriate
torque.
9. Do not operate the changeover switch when the
motor is running.
same
10. Do not use this screwdriver for tightening wood
screws.
11. Whenever a tool is not being used, move the
changeover switch to the "O" (Off) position and
unplug the screwdriver.
12. Do not overload to the extent that the motor locks
or the clutch malfunctions. May cause smoke, fire,
failure or injury.
13. If the body is overheating or functioning
abnormally, stop using the driver immediately and
off
inspect it to see whether any repairs are necessary.
May cause failure or injury.
14. The driver may overheat depending on the type of
screw, type
frequency of use. To avoid overheating, stop
operating the driver for a time or use several
drivers in alternation.
Overheating may reduce the life of the product or
cause failure, burns, or other injuries.
15. The fastening torque may vary depending on how
the product is operated or held, the type of screw,
and the fastening conditions. Use a torque wrench
or similar tool to check that the fastening torque is
appropriate.
16.
The product's output torques shown here are the
values obtained with the following measuring
. This value may differ when measuring
instruments
with different equipment.
･Dedicated device: DLV02/12 series: DLT1173
DLV12SL-CKE
DLV12SL-BKE
0.2 0.15
to
1.33 to 10.6
700
20 to 30 V DC
0.5 ON / 3.5 OFF
2.2 1.4
to
#4 or less
2.0 1.4
to
Unit
mm
0.47 kg / 1.03 lbs
67 dB (uncertainty: K=3dB)
78 dB
3.8 m/s
Bit No.1x3.8x50: 1Pic
Bit No.2x4x50: 1Pic
3
of screw-tightened
DLV16 series: DLT1673
DLV16SL-CKE
DLV16SL-BKE
1.2 0.2
to
1.8 to 14.2
1000
to
48
3.0 2.2
to
#2 to #8
2.6 2.0
to
A B
In 0.28 0.91
7 23
2
Bit No.1x3.8x50: 1Pic
Bit No.2x4x50: 1Pic
material, or
1.6
to
4.0
to
3.0
to
C D
0.35 1/4
9 6.35