Ryobi PAD01 Manuel D'utilisation page 7

CONTROL BUTTONS
See Figure 2, page 9.
Use the control buttons to turn the speaker on and off, play
and pause audio, disconnect BLUETOOTH
the volume, and track forward and back.
NOTE: The USB charging port beside the control buttons
can be used to charge small USB devices.
TURNING THE SPEAKER ON AND OFF:
Press the on/off button to turn the speaker on and off.
When the speaker is on, a battery pack is installed, and a
BLUETOOTH enabled device is paired the LED light will
®
turn solid. If the battery charge is low, the LED will pulse.
NOTE: When the battery charge is low, the speaker will say
"Battery Low".
PLAYING AND PAUSING AUDIO:
When streaming audio from a BLUETOOTH
press the PLAY/PAUSE button to pause the track and press
it again to resume.
DISCONNECTING BLUETOOTH
Press and hold the PLAY/PAUSE button for three seconds
to disconnect a paired BLUETOOTH
ADJUSTING THE VOLUME:
When the speaker is turned on, the unit will return to the last
volume setting used.
 To increase the volume, press the VOL + button.
 To decrease the volume, press the VOL – button.
NOTE: Volume for any connected device can be adjusted
using the volume control for that device and/or with the
VOL + or VOL – buttons on the product.
SCANNING MEDIA TRACKS:
When streaming audio from a BLUETOOTH
press the SCAN left or SCAN right arrow buttons to go to
the previous or next track.
NOTE: These controls may not be supported by the
BLUETOOTH device and/or application you are using.
®
USING A BLUETOOTH
(NOT INCLUDED) WITH THE SPEAKER
See Figure 3, page 10.
 Install a battery pack and turn the speaker on.
NOTE: The speaker will say "Power On" and automatically
attempt to connect to the last device it was paired to. If
no device has been previously paired, the LED will flash.
NOTE: MAINTENANCE INFORMATION BEGINS ON PAGE 8 AFTER
OPERATION
devices, control
®
enabled device,
®
DEVICES:
®
device.
®
enabled device,
®
ENABLED DEVICE
®
FRENCH AND SPANISH LANGUAGE SECTIONS.
ILLUSTRATIONS START ON PAGE 9.
 Set your device to search/scan for available BLUETOOTH
signals, then select "RYOBI PAD01" from the list. No
password or PIN is required for connection.
NOTE: For best results, BLUETOOTH
should be within 50 ft. of the radio and set to search/scan
in order to pair with the radio.
 When the device has successfully paired with the speaker,
the speaker will say "Bluetooth Connected" and the LED
will turn solid.
NOTE: If the speaker does not pair with your device, turn
the power to the speaker off, wait 5 seconds, then turn
the power back on and start the pairing process again.
NOTE: When a device is paired to the speaker, information
for connecting to the device is saved in the speaker's
memory.
 To disconnect the BLUETOOTH
and hold the PLAY/PAUSE button for three seconds.
When the device is disconnected, the speaker will say
"BLUETOOTH
speaker will search for a BLUETOOTH
NOTE: The speaker will not automatically connect to the
device it was just disconnected from.
USING THE USB DEDICATED CHARGING PORT
See Figure 4, page 10.
The USB dedicated charging port provides charging power
of 5 Volts DC at up to 2.1 Amp for your cell phone, MP3
player, or other USB devices.
NOTICE:
Attempting to charge devices rated more than 2.1 Amp,
such as a tablet, could damage the USB dedicated
charging port and/or the device.
 Connect one end of a USB cable (not provided) to your
USB device.
 Connect the other end of the USB cable (not provided) to
the USB dedicated charging port to begin charging the
device.
NOTE: The USB dedicated charging port provides
power only; it does not provide any data communication
capabilities.
 The USB dedicated charging port will continue to function
as long as the speaker is on. If the speaker is off, charging
will stop.
NOTE: The speaker will turn off in two hours if no audio
has been streamed. Turn the speaker on to resume
operation.
7 - English
®
enabled device, press
®
disconected", the LED will flash, and the
®
®
®
enabled devices
signal.