Speaker Connections - JVC KS-AX3004 Manuel D'instructions

SPEAKER CONNECTIONS

Connection varies depending on the number of the speakers used in your car. Select the
appropriate connection referring to the following diagrams.
Notes
• Securely connect all the parts. If the connections are loose, due to contact resistance etc., heat
will break out and may cause an accident.
• Run the connection leads under the car mats to prevent accidental disconnections.
KS-AX3004
4-speaker system—Normal Mode
JVC car receiver, etc.
Line out
(Front)
Filter switches
2
*
REAR REAR
FRONT FRONT FRONT FRONT
b Speaker input connector
Connector lead
Å Gray "FRONT RIGHT (+)"
ı White "FRONT LEFT (+)"
Ç Black "RECEIVER GND"
Î Purple "REAR RIGHT (+)"
‰ Green "REAR LEFT (+)"
2-speaker system plus subwoofer—Bridge Mode
JVC car receiver, etc.
Line out
(Front)
Filter switches
2
*
FRONT FRONT REAR REAR FRONT
FRONT
b Speaker input connector
Connector lead
Å Gray "FRONT RIGHT (+)"
ı White "FRONT LEFT (+)"
Ç Black "RECEIVER GND"
Î Purple "REAR RIGHT (+)"
‰ Green "REAR LEFT (+)"
2-speaker system—Bridge Mode
JVC car receiver, etc.
Line out
Filter switches
2
*
FRONT FRONT REAR REAR FRONT FRONT
b Speaker input connector
Connector lead
Å Gray "FRONT RIGHT (+)"
ı White "FRONT LEFT (+)"
Ç Black "RECEIVER GND"
Î Purple "REAR RIGHT (+)"
‰ Green "REAR LEFT (+)"
EN_KSAX3004_3002[JEU]3.indd 2 EN_KSAX3004_3002[JEU]3.indd 2
All manuals and user guides at all-guides.com
Line out
(Rear)
FRONT REAR REAR
2
*
Front speaker
REAR
(Left/Right)
Rear speaker (Left/Right)
To Receiver
=
Front right (+) lead
=
Front left (+) lead
=
Chassis* 1
=
Rear right (+) lead
=
Rear left (+) lead
Line out
(Rear) or
Subwoofer
out
FRONT REAR REAR
2
*
Front speaker Subwoofer
REAR
(Left/Right)
To Receiver
=
Front right (+) lead
=
Front left (+) lead
=
Chassis* 1
=
Rear right (+) lead
=
Rear left (+) lead
FRONT REAR REAR
Front speaker
(Left/Right)
REAR
To Receiver
=
Left (+) lead
=
Chassis* 1
=
Right (+) lead
a When your receiver is equipped with line output, connect the line output (through the
receiver) to the INPUT jacks on this unit.
b When your receiver is NOT equipped with line output, connect the provided speaker input
connector (through the receiver) to the HIGH INPUT terminal on this unit.
• Connect each lead of the speaker input connector to a speaker positive lead or chassis*
the receiver.
• Cover the terminals of unused speaker negative leads of the receiver with insulating tape to
prevent short circuits.
* 1 Example:
1
*
Black lead of the speaker input connector
RECEIVER
GND
KS-AX3002
2-speaker system—Normal Mode
Filter switch
b Speaker input connector
Connector lead
Å White "LEFT (+)"
ı Black "RECEIVER GND"
Ç Gray "RIGHT (+)"
2-speaker system (2 amplifi ers)—Bridge Mode
b Speaker input connector
Connector lead
Å White "LEFT (+)"
ı Black "RECEIVER GND"
Ç Gray "RIGHT (+)"
Filter switches
b Speaker input connector
Connector lead
Å White "LEFT (+)"
ı Black "RECEIVER GND"
Ç Gray "RIGHT (+)"
Subwoofer system—Bridge Mode
Filter switch
Line out (Rear) or
Subwoofer out
b Speaker input connector
Connector lead
Å White "LEFT (+)"
ı Black "RECEIVER GND"
Ç Gray "RIGHT (+)"
2
* RCA pin cords (not provided)
2
Rear ground terminal
JVC car receiver, etc.
JVC car receiver, etc.
Line out
2
*
To Receiver
=
Left (+) lead
=
Chassis* 1
Right Left
=
speaker speaker
Right (+) lead
JVC car receiver, etc.
To Receiver
=
Line out
Left (+) lead
=
Chassis* 1
=
Left (+) lead
2
*
Left speaker
To Receiver
Right speaker
=
Right (+) lead
=
Chassis* 1
=
Right (+) lead
JVC car receiver, etc.
2
*
To Receiver
=
Left (+) lead
=
Chassis* 1 Subwoofer
=
Right (+) lead
1 of
08.5.14 8:34:41 PM 08.5.14 8:34:41 PM