Adjusting The Speaker Volume; Adjusting The Delay Time - Sony SDP-E800 Mode D'emploi

Processeur surround
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Sub woofer
Initial setting is : SUB WOOFER [YES]
• If you connect a sub woofer, select "YES" to output
the LFE (low frequency extension) channel from the
sub woofer.
• If you do not connect a sub woofer, select "NO". This
activates the Dolby Digital (AC-3) bass redirection
circuitry and outputs the LFE signals from other
speakers.
• In order to take full advantage of the Dolby Digital
(AC-3) bass redirection circuitry, we recommend
setting the sub woofer's cut off frequency as high as
possible. (However, when using an amplifier with 5.1
ch inputs, set the sub woofer's cut off frequency to
match the characteristics of the amplifier.)
4
Use digital processing control buttons ( / ) to
adjust the level of the parameter.

Adjusting the delay time

The delay time allows you create a more effective
surround effect by adding a sense of depth to the
centre or rear channels. Longer delay times create a
greater sense of depth.
1
Press POWER on the front panel to turn on the
processor.
2
Press DPC MODE repeatedly until "OTHER
SETUP" appears in the display
3
Use digital processing control buttons (
select the parameter you want.
Centre speaker delay
Initial setting is : CENTER DELAY 0ms
Use this parameter to add a sense of depth to the centre
channel.
• Centre speaker delay time can be set in 1 ms steps
from 0 to 5 ms.
Rear speaker delay
Initial setting is : REAR DELAY 5ms
Use this parameter to add a sense of depth to the rear
channels.
When "PRO LOGIC" is displayed, the actual delay time
is 15ms longer than the time shown in the display.
• Rear speaker delay time can be set in 5 ms steps from
0 to 15 ms.
4
Use digital processing control buttons ( / ) to
adjust the level of the parameter.

Adjusting the speaker volume

Use the remote while seated in your listening position
to adjust the volume of each speaker.
2
A
2
B
2
C
2
D
Note
This unit incorporates a new test tone with a frequency
centreed at 800 Hz for easier speaker volume adjustment.
1
Press TEST.
You will hear the test tone from each speaker in
sequence.
2
From your listening position, use the remote to
adjust the volume of each speaker so that the test
tone can be heard at the same level from all
speakers.
A
Press FRONT BAL L or R to adjust the balance
/
) to
between the front left and right speakers (±8
dB, 0.5 dB/steps).
During this adjustment, the test tone is emitted
from both speakers simultaneously.
B
Press REAR BAL L or R to adjust the balance
between the rear left and right speakers (±8 dB,
0.5 dB/steps).
During this adjustment, the test tone is emitted
from both speakers simultaneously.
C
Press CENTER + or – to adjust the level of
centre speaker (+10 to –20 dB, 0.5 dB/steps).
During this adjustment, the test tone is emitted
from the centre speaker.
D
Press REAR + or – to adjust the level of rear
speakers (+10 to –20 dB, 0.5 dB/steps).
During this adjustment, the test tone is emitted
from both speakers simultaneously.
E
Press SUB WOOFER + or – to adjust the level
of the sub woofer (+10 to –20 dB, 0.5 dB/steps).
During this adjustment, the test tone is emitted
from the sub woofer.
3
Press TEST to turn off the test tone.
Getting Started
Getting Started
1, 3
2
E
MASTER
VOLUME
(continued)
9
GB

Publicité

Table des Matières
loading

Table des Matières