Miele MF03 10 Notice De Montage page 40

Produktgruppe 512
40 von 42
Note
Installation kit mat. no. 09079460 for PW 6107, PW 6137 , PW 6167 and PW 6207 contains:
1 EZL 235 electronic, module 5 (liquid dispensing 7-11 and WRG)
4 spacers (for securing the EZL 235 electronic)
1 coded plug MFM 3-5 (module 3 EZL 235 ST3), pin 3-5
1 coded plug WRG 1 (module 3 EZL 235
1 coded plug MFM 53X (module 3 EZL 235
1 plug N1Q-ST11A (module 3 EZL 235 ST11), pin 1-2
1 wiring harness 20X-41X (module 3 EZL 235
1 wiring harness N1Q_ST112, N1Q_ST11 (module 3 EZL 235
3 black wires, 0.75x90
1 screw terminal 4-pin/ecru
1 screw terminal 4-pin/red
1 screw terminal 6-pin/blue
1 screw terminal 7-pin/green
1 terminal strip 1X3-4 orange
1 terminal strip 2X3-4 gray
1 terminal strip 3X3-4 blue
1 terminal strip 4X3-4 green/yellow
1 liquid dispensing accessory
1 wiring diagram, PW 6107 PW 6207 module 2, mat. no. 09082720
These instructions, mat. no. 09087201.
Note
Installation kit mat. no. 09885150 for PW 6107, PW 6137 , PW 6167 and PW 6207 contains:
1 EZL 235 electronic, module 5 (liquid dispensing 7-11 and WRG)
4 spacers (for securing the EZL 235 electronic)
1 coded plug MFM 3-5 (module 3 EZL 235 ST3), pin 3-5
1 coded plug WRG 1 AWG (module 3 EZL 235
1 coded plug MFM 53X AWG 20 (module 3 EZL 235 ST7), pin 1-2, 3-4
1 plug N1Q-ST11A AWG (module 3 EZL 235
1 wiring harness 20X-41X SIF18 (module 3 EZL 235
1 wiring harness N1L_ST11BN1Q_ST11AWG (module 3 EZL 235
350 mm
3 brown wires, AWG 20x90
1 screw terminal 4-pin/ecru
1 screw terminal 4-pin/red
1 screw terminal 6-pin/blue
1 screw terminal 7-pin/green
1 terminal strip 1X3-4 orange
1 terminal strip 2X3-4 gray
1 terminal strip 3X3-4 blue
1 terminal strip 4X3-4 green/yellow
1 liquid dispensing accessory
1 wiring diagram PW 6107 PW 6207 module 2, mat. no. 09082720
These instructions, mat. no. 09087201.
List of illustrations:
Fig. 1, EZL 235 electronic installation
Fig. 2, EZL 235 wiring, module 3, liquid dispensing 7-11 and water recycling (WRG)
Fig. 3, Installing the cable guide on the connection strip
Disconnect the machine from the electrical supply and gas supply (if applicable) and ensure that power cannot be switched on again
in error.
Remove the left and right screws from the machine lid.
Pull the lid slightly forward, push it back and unhook it from the connection strip.
Remove the lid.
Install the EZL 235 electronic with the 4 spacers in the pre-existing holes on the side of the module holder; see Fig. 1, Pos. 1, Pos. 2.
Install the terminal strips in the pre-existing holes on the module holder; see Fig. 1, Pos. 3.
06.02.2014 Diese Unterlagen dürfen ohne unsere Genehmigung weder vervielfältigt noch Dritten zugänglich gemacht werden. Eigentumsrechte vorbehalten.
ST6), pin 2-3
ST7), pin 1-2, 3-4
ST10 / module 1 EZL 235
ST111 / module 1 EZL 235
ST6), pin 2-3
ST11), pin 1-2
ST10 / module 1 EZL 235 ST9), plug housing 3-pin, 500 mm
ST111 / module 1 EZL 235
Umbau- und Montageanweisung
M.-Nr. 09087201
ST9), 3-pin, 500 mm
ST112), 4-pin, 350 mm
ST112), plug housing 4-pin,