Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
•
Grasp recoil starter handle with one hand and grasp
tiller handle with other hand. Pull rope out slowly until
engine reaches start of com pres sion cycle (rope will
pull slightly harder at this point).
•
Pull recoil starter handle quickly. Do not let starter
handle snap back against starter.
•
If engine fires but does not start, move choke control
to half choke position. Pull recoil starter handle until
engine starts.
•
When engine starts, slowly move choke control to
"RUN" position as engine warms up.
NOTE: A warm engine requires less choking to start.
•
Move throttle control to desired running position.
•
Allow engine to warm up for a few minutes before
engaging tines.
NOTE: If at a high altitude (3000 feet) or in cold tem per a tures
(below 32°F), the carburetor fuel mixture may need to be
adjusted for best engine performance. If you think the fuel
mixture needs adjusting, contact your nearest authorized
service center/department, which has the proper equip-
ment and experience to make any nec es sary adjustments.
NOTE: If engine does not start, see troubleshooting points.
THROT TLE
CON TROL
CHOKE
CON TROL
RECOIL
STARTER HANDLE
TILLING HINTS
CAUTION: Until you are accustomed to
handling your tiller, start actual field use
with throttle in slow position (mid-way
between "FAST" and "IDLE").
•
Tilling is digging into, turning over, and breaking up
packed soil before planting. Loose, unpacked soil
helps root growth. Best tilling depth is 4" to 6" (10-15
cm). A tiller will also clear the soil of unwanted veg-
e ta tion. The de com po si tion of this vegetable mat ter
enriches the soil. Depending on the climate (rain fall
and wind), it may be advisable to till the soil at the end
of the growing season to further condition the soil.
•
You will find tilling much easier if you leave a row un-
tilled between passes. Then go back between tilled
rows. (See Fig. 13) There are two reasons for doing
this. First, wide turns are much easier to negotiate than
about-faces. Sec ond, the tiller won't be pulling itself,
and you, toward the row next to it.
OPERATION
Fig. 12
4
5
•
Soil conditions are important for proper tilling. Tines will
not readily penetrate dry, hard soil which may con trib ute
to excessive bounce and difficult handling of your tiller.
Hard soil should be mois tened before tilling; however,
extremely wet soil will "ball-up" or clump during tilling.
Wait until the soil is less wet in order to achieve the
best results. When tilling in the fall, re move vines and
long grass to prevent them from wrapping around the
tine shaft and slowing your tilling operation.
•
Do not lean on handle. This takes weight off the wheels
and reduces traction. To get through a really tough
section of sod or hard ground, apply upward pressure
on handle or lower the depth stake.
CULTIVATING
Cultivating is destroying the weeds between rows to pre vent
them from robbing nourishment and moisture from the
plants. At the same time, breaking up the upper layer of
soil crust will help retain moisture in the soil. Best digging
depth is 1" to 3" (2.5-7.5 cm). Lower the outer side shields
to protect small plants from being buried.
•
Cultivate up and down the rows at a speed which will
allow tines to uproot weeds and leave the ground in
rough condition, promoting no further growth of weeds
and grass (See Fig. 14).
TINE SHEAR PINS
The tine assemblies on your tiller are secured to the tine
shaft with shear pins (See "TINE REPLACEMENT" in the
Service and Ad just ments section of this manual).
If the tiller is unusually overloaded or jammed, the shear
pins are designed to break before internal damage occurs
to the trans mis sion.
•
If shear pin(s) break, replace only with Original Equip-
10
ment Manufacturer (O.E.M.) replacement parts.
3
2
1
6
7
Fig. 13
Fig. 14
Publicité
Chapitres
Table des Matières
