Protection Against Overheating; Replacing The Power Cable; Disposal And Recycling; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TH-HA 2000/1 Instructions D'origine

Pistolet à air chaud
Masquer les pouces Voir aussi pour TH-HA 2000/1:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 19
Accentuation of natural wood grains before
staining or lacqueing.
Shrinkage of PVC packaging foils and insula-
tion tubes.
Waxing and de-waxing of skis.
Caution: Intensive heating means a higher
risk of fi re and explosion! Ensure good venti-
lation. Harmful and/or toxic gases and vapors
may be emitted.
6.3 Selecting the right nozzle
The heat nozzle (4) is designed to protect e.g.
glass panes from overheating by diverting the
hot air. For removing paint.
The wide nozzle (5) provides uniform air dis-
tribution on small surfaces
The reducer nozzle (6) provides a targeted jet
of heat for corners and for soldering work.
The reflector nozzle (7) is designed for solde-
ring and shaping tubes, for defrosting water
pipes and for shrinking insulating hoses.

6.4 Protection against overheating

To prevent overheating, the device is equipped
with a thermostatic switch. In the event of exces-
sively high temperatures inside the device, this
will switch the heating element off while the fan
continues running. As soon as the temperature
is in the normal range again, the heating element
will be switched on again.

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
Anl_TH_HA_2000_1_SPK9.indb 15
Anl_TH_HA_2000_1_SPK9.indb 15
GB
pressure.
We recommend that you clean the device
immediately each time you have finished
using it.
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
8.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.3 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info

9. Disposal and recycling

The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.
10. Storage
Store the equipment and accessories in a dark
and dry place at above freezing temperature. The
ideal storage temperature is between 5 and 30
°C. Store the electric tool in its original packaging.
- 15 -
04.12.2019 15:54:14
04.12.2019 15:54:14

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

4520179

Table des Matières