Product Description And Specifications; Intended Use; Product Features; Technical Data - Bosch GWS 12V-76 Professional Notice Originale

the cut. The wheel may bind, walk up or kickback if the
power tool is restarted in the workpiece.
Support panels or any oversized workpiece to minim-
u
ize the risk of wheel pinching and kickback. Large
workpieces tend to sag under their own weight. Supports
must be placed under the workpiece near the line of cut
and near the edge of the workpiece on both sides of the
wheel.
Use extra caution when making a "pocket cut" into ex-
u
isting walls or other blind areas. The protruding wheel
may cut gas or water pipes, electrical wiring or objects
that can cause kickback.
Additional safety information
Wear safety goggles.
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
Do not touch grinding and cutting discs until they have
u
cooled down. The discs can become very hot while work-
ing.
Release the On/Off switch and set it to the Off posi-
u
tion when the power supply is interrupted, e.g. when
the battery pack is removed. This prevents uncontrolled
restarting.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Do not touch grinding discs until they have cooled
u
down. The discs can become very hot while working.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Bosch Power Tools
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.

Intended use

The power tool is intended for cutting and roughing of metal,
stone and wood materials, plastics, non-ferrous metals and
tiles without the use of water. A specific protective guard
must be used when cutting.

Product Features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Direction of rotation arrow on housing
(2) Spindle lock button
(3) On/off switch
A)
(4) Battery
A)
(5) Battery release button
(6) Battery charge indicator
(7) Protective guard for grinding
(8) Grinding spindle
(9) Handle (insulated gripping surface)
(10) Protective guard for cutting
(11) Clamping bolt with washer
A)
(12) Cutting disc
(13) Hex key
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical Data

Grinder
Article number
Rated voltage
A)
Rated speed
Max. grinding disc diameter
Mounting diameter
Weight according to EPTA-
A)
Procedure 01:2014
Recommended ambient
temperature during char-
ging
Permitted ambient temper-
B)
ature during operation and
during storage
English | 17
A)
GWS 12V-76
3 601 JF2 0..
V= 12
-1
min 19,500
mm 76
mm 10
kg 0.70–0.90
°C 0 to +35
°C -20 to +50
1 609 92A 54P | (18.07.2019)