Tbox-Luce Controls - Whirlpool HLB 9.5S AT/HA Mode D'emploi

TBOX-LUCE controls

Models with Touch control glass (basic)
HLB 9.5S AT(ICE)/HA - HLB 6.8 LT X/HA
HLB 6.7 AT X/HA - HLB 9.7 AT X/HA
T1 T2 T3 T4
T1 motor ON/OFF
When the button is pressed with the hood off, the first speed
is set. When the button is pressed during operation, the
hood switches OFF.
T2 Speed 1
When the button is pressed the hood switches from the
previous status to speed 1.
T3 Speed 2
When the button is pressed the hood switches from the
previous status to speed 2.
T4 Speed 3
When the button is pressed the hood switches from the
previous status to speed 3.
T5 Booster
When the button is pressed the hood switches from the
previous status to intense speed. The setting is limited by
time; when the time elapses the hood goes back to the speed
set previously; when a speed button is pressed (T2, T3 or
T4), the selected speed is set as you leave the booster mode.
T6 Timer
By pressing T6 once, a timer setting can be associated
to each speed V) [v1 – 30 min, v2 – 20 min, v3 – 10 min]
, after which the hood turns OFF automatically. The timer
can be set for manual speeds only and not for the booster.
T7 Antigrease and odour filter signal
The antigrease (A) and odour (B) filters need cleaning/
replacing after a certain number of hours of use (the latter
for filtering hoods only).
The time for cleaning/replacement is signalled by the
flashing of the coloured LED associated to the filter (white
for antigrease filters, red for odour filter).
The LED is turned off by pressing the T7 button after
cleaning/replacing the filters.
T8 lights ON/OFF
It turns the work lights of the hood on and off.
Hood configuration
The configuration menu is accessed with the product off
by pressing T5 and T6 for 6 seconds. T7 turns on at this
point to indicate the type of installation through two colours
of the LED: white for extractor installation (default), red for
filtering installation. The installation type can be changed
by pressing T7 cyclically with the consequent alternation
of the LED colours.
Hood off
The hood can be turned off manually by pressing the T1
button (ON/OFF). If the timer is set, the hood turns off
automatically when the set time runs out.
Models with Touch control glass + display
(medium)
T5 T6 T7 T8
T1 motor ON/OFF
When the button is pressed with the hood off, the first speed
is set. When the button is pressed during operation, the
hood switches OFF.
T2 Speed –
When the button is pressed the hood switches to the
previous speed.
T3 Speed +
If the hood is set to speed 3, the intensive speed activates
when this button is pressed
The setting is limited by time; when it elapses the hood goes
back to the speed set previously.
T4 Timer "–"
Set a time to turn OFF the hood with the timer; if the timer
is set and the speed is subsequently changed by pressing
T2, T3 or T4, the timer is deactivated.
Press T4 to decrease the timer by 5 minutes.
T5 Timer "+"
When the button is pressed for the first time, the timer is set
to 5 minutes; this value is increased by 5 additional minutes
every time the button is pressed after that.
T6 lights ON/OFF
It turns the work lights of the hood on and off
D1: DGT Speed
D2: Assembly of 2 DGT Time
I1: Grease Filter Indicator
I2: Carbon Filter Indicator
I4: Menu Indicator
I5: Timer Indicator
HLB 9.8 AADC X/HA - HLB 9.8 AA X/HA
T1 T2 T3
I1 D1 D2
I2
GB
T4 T5 T6
I5
I4
31