Inglesina TRILOGY Instructions D'utilisation page 24

CHASSIS
ASSEMBLY/REMOVAL OF REAR WHEEL ASSEMBLY
¿J  Insert the wheel assembly in correspondence of the rear tube
¿J  Attach the ring (T5) to the bracket (T6), and press the lever (T7) until it is fully
attached, making sure that the ring (T5) is properly positioned in its housing.
CAUTION: make sure that the wheels are properly attached before use.
¿J  To remove the rear wheel assembly, lift the lever (T7) and unhook the ring (T5)
from the bracket (T6), until it is completely free.
OPENING THE CHASSIS
¿J  .HHSLQJ SUHVVHG WKH OHYHU T8 SRVLWLRQHG RQ WKH ULJKW KDQGOH ¿UPO\ OLIW WKH IUDPH
until it is completely open.
¿J  Complete the procedure by pushing on the pedal control (T9) until it is locked in
KRUL]RQWDO SRVLWLRQ
¿J  &$87,21 PDNH VXUH WKDW DOO FORVLQJ PHFKDQLVPV DUH SURSHUO\ DWWDFKHG
on both sides before use.
CLOSING THE CHASSIS
¿J  3UHVV WKH EXWWRQ T10) and lift the rear handle (T11).
¿J Firmly pull the rear handle (T11) upwards until the chassis is completely folded
REAR WHEELS BRAKE
¿J  To engage the brake, push down the lever (T12) positioned on the right rear wheel
assembly
Always engage the brake during stops.
CARRY HANDLE
¿J  To transport the folded chassis, use the handle (T13). Do not lift the chassis by the
opening handle (T11).
BLOCKING/UNBLOCKING THE FRONT WHEELS
¿J  7KH FKDVVLV LV HTXLSSHG ZLWK VZLYHO ZKHHOV ZKLFK FDQ EH EORFNHGXQEORFNHG E\
means of the lever (T15 ORFDWHG LQ FRUUHVSRQGHQFH RI WKH FHQWUDO MRLQW
REMOVING THE FRONT WHEELS
¿J  If necessary, the front wheels can be easily removed. To do so, push the lever
(T16 IRUZDUGV DV VKRZQ LQ WKH ¿JXUH DQG VLPXOWDQHRXVO\ UHPRYH WKH ZKHHO
¿J  To reattach the wheels, insert them in correspondence of the opening (T17) and
push until it clicks into place.
CAUTION: make sure that the wheels are properly attached before use.
REAR PLATFORM
¿J  $GMXVW WKH UHDU SODWIRUP T9) with your foot to cross obstacles.
FEEDING BOTTLE HOLDER
¿J  7KH FKDVVLV LV HTXLSSHG ZLWK D VWDQGDUG IHHGLQJ ERWWOH KROGHU T3).
To fasten the feeding bottle holder, place the upper guide in correspondence of the hook
(T18) on the chassis and push it in its housing until it is fully attached.
STORAGE BASKET
¿J  7KH FKDVVLV LV HTXLSSHG ZLWK D FDSDFLRXV VWRUDJH EDVNHW T4). To secure it, insert
the eyelets (B1) onto the rear hooks (T19) on the chassis.
/HW WKH ¿QV B2) pass through the eyelets (T20) on the side of the frame and fasten the
corresponding press studs.
Finally, insert the eyelets (B3) onto the front hooks (T21) on the chassis
24