Maintenance And Cleaning; Putting Into Operation; Ordering Replacement Parts - EINHELL DTA 25/2 Instructions D'utilisation Et D'entretien

Anleitung DTA 25-2_SPK1
GB
Do not remove any protective devices or contact
guards.
Never leave the tool unattended when loaded.
Never use defective tools.
Use only original Einhell staples/nails.
When the tool is disconnected it must not be under
any pressure.
Never use the tool without staples.
Never point an operational stapler directly at
yourself or at any other person.
Whilst working with the stapler, hold it in such a
way that your head and body cannot be injured in
case of kickback caused by disruption of the
power supply or by hard areas of the workpiece.
Never trigger the stapler into the open air. This is
important to avoid the hazards of free-flying
staples and of overloading the appliance.
For the purposes of transportation, the stapler
must be disconnected from the compressed-air
system, especially if you are using a ladder or are
adopting an unusual posture.
In the workplace, carry the stapler only by its
handle and ensure that the trigger is inactivated.
Make allowance for the workplace conditions.
Staples can potentially go straight through thin
workpieces or they can slide off workpieces when
working on corners and edges, thus putting
persons at risk.
For you own personal safety, always use suitable
protective equipment such as, for example,
hearing and eye protection.

5. Putting into operation

Screw the supplied plug-in nipple into the air
connection.
To fill the magazine, press on the magazine lever
and pull back the lower magazine shaft as far as the
stop. Insert the staples/nails into the magazine rail
from above. Do not insert more than one complete
stick of staples/nails or the magazine will be too full
and can no longer be closed. After connecting the
stapler to the air supply, place it in stapling/nailing
position and pull the trigger lever. The trigger lever
has to be released after each shot.
Automatic operation: If you keep the trigger lever
pressed, the staples/nails will be shot automatically
when the stapler is placed against the workpiece.
Be careful not to staple twice in the same place.
Caution !
If a staple/nail becomes stuck in the piston shaft, first
disconnect the stapler and make sure it is not under
any pressure before you remove the cover plate.
6
07.07.2006 9:52 Uhr Seite 6
With the magazine open and the rest of the
staples/nails removed you can then take out the
jammed staple. Clean the shaft if necessary and
close again.

6. Maintenance and cleaning

Observance of the following maintenance
instructions will ensure that this quality tool gives you
years of troublefree service.
Before starting to work, always check that the
magazine is secure. Clean the tool thoroughly when
you are finished with your work.
Regular lubrication is vital for the long-term, reliable
operation of your stapler. Use only special tool oil for
this purpose.
You can choose from the following options for
lubricating the tool:
6.1 By mist oiler
A complete conditioning unit includes a mist oiler and
is fitted to the compressor.
6.2 By hand
If your air system has neither a conditioning unit nor
a line oiler, you must feed 3-5 drops of special tool oil
into the air connection each time before you use your
stapler. If the pneumatic tool has not been used for
several days, you must feed 5-10 drops of oil into the
air connection before you switch on.
Keep your pneumatic tool in dry rooms only.

7. Ordering replacement parts

Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
The warranty does not cover:
Wearing parts
Damage caused by an unacceptable level of
working pressure.
Damage caused by unconditioned compressed
air.
Damage caused by improper use or unauthorized
tampering.