Installation; General - Hatco FTBR Série Manuel D'installation Et D'utilisation

INSTALLATION

General

Remote Frost Top Drop-In Shelves are shipped from the factory
as components that require installation and connection. Use
the following procedures to install each component and make
the appropriate connections.
WARNING
ELECTRIC SHOCK HAZARD:
• Units supplied without an electrical cord and plug
require a hardwired connection to on-site electrical
system. Connection must be properly grounded and
of correct voltage, size, and configuration for electrical
specifications of unit. Contact a qualified electrician to
determine and install proper electrical connection.
• Unit is not weatherproof. Locate unit indoors.
FIRE HAZARD: Install condensing unit with a minimum of
6" (152 mm) of space between all sides of unit and any
combustible surfaces.
This unit must be installed by qualified, trained installers.
Installation must conform to all local electrical and
plumbing codes. Check with local plumbing and electrical
inspectors for proper procedures and codes.
CAUTION
Locate the unit at the proper counter height in an area
that is convenient for use. The location should be level
and strong enough to support the weight of the unit and
contents.
NOTICE
This unit is designed for use in environments where the
ambient temperature is between 65°F (18°C) and 86°F
(30°C).
Provide louvered or grill-style openings with a minimum
size of 12" x 12"/144 square inches (31 x 31 cm/
961 square cm) in the cabinetry in front of and behind the
condensing unit for proper ventilation. Failure to provide
adequate air flow through the condensing unit may cause
unit failure and will void the unit warranty.
Transport and install unit in upright position only. Failure
to do so may result in damage to the refrigeration system.
Do not locate unit in an area subject to excessive
temperatures or grease from grills, fryers, etc. Excessive
temperatures could cause damage to the unit.
All Remote Frost Top Drop-In Shelves are shipped in a shipping
frame for protection and stability. Keep the unit in the shipping
frame until the unit and the installation site are completely
prepared for the unit to be installed.
1. Remove all external packaging from the unit.
2. Remove tape, protective packaging, and literature from all
surfaces of unit.
NOTE: To prevent delay in obtaining warranty coverage,
complete online warranty registration. See the
IMPORTANT OWNER INFORMATION section for
details.
3. Cut the appropriate opening in the countertop for the unit
being installed. Refer to "Countertop Cutout Dimensions"
in this section.
4. Cut and drill the appropriate holes in the vertical surface
where the control panel will be installed. Refer to the
"Installing the Control Panel" procedure in this section for
cutout and hole dimensions.
5. Make structural modifications or add bracing underneath
the countertop to ensure the countertop will support the
weight of the unit and its contents.
NOTE: The countertop must be level to ensure proper draining
of the frost top enclosure.
6. Lift the unit out of the shipping shipping frame and carefully
lower it into the countertop cutout. This step requires two
or more people, depending on the unit.
Installing a FTBR-2 Model
7. Apply National Sanitation Foundation-approved (NSF-
approved) silicone sealant around the edge of the unit to
seal it to the countertop.
NOTE: If excessive condensation appears underneath the
countertop during operation, apply polyurethane-based
foam sealant in the gap between the underside of the
countertop and the frost top.
8. For two and three pan units, connect the 1" drain fitting
to a trap and drain line. If a trap and drain line are not
available, a catch pan (not supplied) must be used under
the drain fitting to contain water draining from the frost top
enclosure.
NOTE: Consult a qualified plumber for proper trap and drain
installation that conforms to local plumbing codes.
9. Install the control panel in the desired location. Refer to the
"Installing the Control Panel" procedure in this section.
10. For FTBR Models, install the condensing unit in the
desired location. Refer to the SPECIFICATION section for
installation dimensions.
• Make sure the installation site offers continuous air flow
ventilation to the condensing unit.
• Make sure there is a minimum of 6" (152 mm) of space
between all sides of the condensing unit and any
combustible surface.
11. Have qualified installers perform the "Connecting the
Components" procedure in this section.
12. Clean the frost top enclosure thoroughly in preparation for
initial operation. Refer to the MAINTENANCE section for
proper cleaning procedures.
NOTE: If a catch pan is used underneath the drain fitting,
make sure the pan is emptied regularly to prevent over-
flowing.
8
English
Full-Size
Sheet Pan
Countertop
Cutout
Form No. FTBRM-0717