Before Starting The Equipment; Noise Emission Values; General Information - Parkside PKS 1700 B2 Mode D'emploi D'origine

Noise emission values

The saw's noise is measured in accordance with
EN 61029.
L sound pressure level ....................... 88,6 dB(A)
pA
K uncertainty .................................................3 dB
pA
L sound power level .......................101,6 dB(A)
WA
K uncertainty ................................................3 dB
WA
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 61029.
Vibration emission value a
K uncertainty = 1.5 m/s
Warning!
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful effect.
Keep the noise emissions and vibrations
to a minimum.
•
Only use appliances which are in perfect
working order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appli-
ance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Anl_4300686.indb 49 Anl_4300686.indb 49
GB
Idle speed
< 2.5 m/s 2
h
2
- 49 -
6. Before starting the
equipment

6.1 General information

•
The equipment must be set up where it can
stand securely, i.e. it should be bolted to a
workbench, a universal base frame or similar.
•
All covers and safety devices have to be pro-
perly fitted before the equipment is switched
on.
•
It must be possible for the blade to run freely.
•
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws, etc.
•
Before you press the ON/OFF switch check
that the saw blade is fitted correctly. Moving
parts must run smoothly.
•
Before you connect the equipment to the po-
wer supply make sure the data on the rating
plate are identical to the mains data.
6.2 Assembling the saw (Fig. 1-2, 4-6)
•
To adjust the turntable (16), loosen the locking
grip (13) by approx. 2 turns and press the
latched position lever (12) to disengage the
turntable (16) (Figure 4).
•
To release the saw from its bottom position,
apply light downward pressure to the machi-
ne head (5). At the same time pull the safety
pin (25) out of the motor mount. Turn the
safety pin (25) through 90° so that the saw
remains unlocked (Fig. 1-2).
•
Swing the machine head (5) up until the re-
lease lever (3) latches into place (Fig. 1).
•
Fit the clamping devices (8) on the left and/or
right side of the fixed saw table (17) (Fig. 1).
•
Undo the locking screws for the workpiece
support (10) (Fig. 5).
•
Mount the workpiece support (9) on the fixed
saw table (17) and tighten the appropriate
locking screw (10) (Fig. 5).
•
Mount the second workpiece support (9) on
the opposite side of the saw and secure with
the appropriate locking screw (10).
•
When the locking screw (23) is loosened, you
can tilt the machine head (5) to the left by up
to 45° (Fig. 1-2).
•
Screw the additional stability bar (18) to the
10.10.12 18:45 10.10.12 18:45