Ferroli OMNIA S 3.2 Manuel D'installation, D'utilisation Et D'entretien page 119

OMNIA S 3.2
Menu Menu
Level 1 Level 2
11.1 Test Run Enable
11.2 Trail run steps
For Serviceman 11 Test Run
11.3 Point Check
For Serviceman 12 Reserved Reserved
13.1 COOL/HEAT MODE
13 Auto
For Serviceman
Restart *
13.2 DHW MODE
14 Power Input
For Serviceman 14.1 POWER LIMITATION
Limitation
15.1 On/Off(M1M2)
15.2 Smart Grid
15.3 T1B(Tw2)
15.4 Tbt1
15.5 Reserved
15,6 Reserved
For Serviceman 15 Input Define
15.7 Solar Input
15.8 F-Pipe Length
15.9 Reserved
15.10 Rt/Ta_Pcb
For Serviceman 16 Reserved
17.1 Reserved
17 Hmi Address
For Serviceman
Set
17.2 Hmi Address For Bms
NOTE
* It allows you to enable or disable the functions that can be restarted in the event of a power failure.
Tabella. 6 - Max current input (A) for different level of power input limitation
Level of power input limitation
Model
4-6
8-10
12-14-16
12T-14T-16T
Menu Menu
Level 3 Level 4
3way-valve 1
3way-valve 2
PUMPI
PUMPO
PUMPC
PUMPSOLAR
PUMPDHW
INNER BACKUP HEATER
TANK HEATER
3WAY-VALVE 3
SOLAR ENABLE
IN SOLAR
0=CN18 Tsolar
/ /
/
/
0 1 2
18 18 16
19 19 18
30 30 28
30 30 29
14 14 13
Cod. 3541V941 - Rev. 00 - 09/2021
Description
TEST RUN ENABLE 0=OFF 1=ON - to activate
the menù "11.2 Trail run steps"
0 = to activate the menù "11.3 Point Check"
1=ON - to activate air purge
2=ON - to activate water pump
3=ON - to activate Cooling mode
4=ON - to activate Heating mode
5=ON - to activate Dhw mode
TEST ON-OFF
It allows you to perform a functional test on indi-
vidual loads, individually forcing their activation
and subsequent shutdown.
It also allows you to temporarily force the system
into specific functional states for testing (air
purge, circ pump running ...)
The on / off action of each function is always
voluntary manual.
Only one function can be switched on / off at a
time, contemporaneity is not allowed.
If a function is on and you exit the Test Run menu
while it is on, the function will automatically shut
down.
Reserved
Auto restart cooling/heating mode.
0=NON,1=YES
Auto restart DHW mode. 0=NON,1=YES
The type of power input limitation (refer to
"Tabella. 6 - Max current input (A) for different
level of power input limitation" a pagina 119).
/
Enable or disable the SMART GRID;
0=NON,1=YES
Enable or disable the T1b(Tw 2) ;
0=NON,1=YES
Enable or disable the Tbt1;
0=NON,1=YES
Reserved
Reserved
Enable solar input:
0 = NOT,
1 = YES
Solar input type;
0 = no solar input;
1 = CN18_Tsolar (to enable Tsolar solar panel
temperature probe);
2 = do not use
Choose the total length of the liquid pipe(F-PIPE
LENGTH); 0=F-PIPE LENGTH: 10m,1=F-PIPE
LENGTH≥ 10m
Reserved
Enable or disable the RT/Ta_PCB;
0=NON,1=YES
/
/
To set the BMS address of the heat pump
3 4
15 14
16 14
26 24
27 25
12 11
Lower Upper Unit of
Resolution
limit limit measure
0 1 1
0 5 1
0 1 1
0 1 1
0 1 1
0 1 1
0 1 1
0 1 1
0 1 1
0 1 1
0 1 1
0 1 1
/ / /
0 1 1
0 1 1
0 8 1
0 1 /
0 1 /
0 1 /
0 1 /
/ / /
/ / /
0 1 1
0 2 1
0 1 1
/ / /
0 1 1
/ / /
/ / /
1 16 1
5 6 7
13 12 12
12 12 12
22 20 18
23 21 19
10 9 9
EN
Default
value
N 0
N 0
N 0
N 0
N 0
N 0
N 0
N 0
N 0
N 0
N 0
N 0
/ /
/ 1
/ 1
/ 0
/ 0
/ 0
/ 0
/ 0
/ /
/ /
/ 0
/ 0
/ 0
/ 0
/ 0
/ /
/ /
/ 0
8
12
12
16
17
9
119