Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
OBJ_BUCH-2516-002.book Page 16 Friday, November 13, 2015 9:25 AM
16 | English
Accessory
BIM plunge cut saw
blades, metal
HM-Riff segment
saw blade
HM-Riff delta plate Mortar, concrete remainders,
Scraper, rigid
BIM serrated seg-
ment saw blade
Mounting/Replacing the Application Tool/Accessory
If required, remove an already mounted application tool/ac-
cessory.
For removing the application tool/accessory loosen the screw
7 with the hex key 8 and remove the tool.
Mount the application tool/accessory (e.g. plunge cut saw
blade 6) in such a way on the tool holder 5 that the openings
of the tool engage into the cams of the tool holder.
For a safe and fatigue-free working position it is possible to
position the application tools/accessories in any snap-in posi-
tions on the tool holder. Position the tool in such a way that
the depressed centre points downwards (marking on the tool
is readable from above, see figure on the graphics page).
Use the screw 7 to fasten the application tool/accessory.
Tightly fasten the screw 7 with the hex key 8.
Check the tight seating of the application tool/accesso-
ry. Incorrect or not securely fastened application tools/
accessories can come loose during operation and pose a
hazard.
Mounting and Adjusting the Depth Stop
The depth stop 11 can be used when working with segment
saw blades, Riff-segment saw blades and segment blades.
If required, remove an already mounted application tool/ac-
cessory.
Slide the depth stop 11 over and beyond the tool holder 5 to
the stop onto the gear head of the power tool with the labelled
side facing upward.
The depth stop is intended for the following cutting depths:
– With segment saw blades ACZ 85 .. with a diameter of
85 mm: 8 mm, 10 mm, 12 mm and 14 mm cutting depths
(see indication on the depth stop in large font and not in
brackets).
1 609 92A 1PU | (13.11.15)
Material
Application
Metal (e. g. unhardened nails,
Smaller separating and plunge cuts;
screws, smaller profiles),
example: shortening narrow profiles, cutting fastening
non-ferrous metals
elements such as staples
Grouting joints, soft wall tiles,
Cutting and separating close to edges, in corners or hard
glass-fibre reinforces plastic
to reach areas;
and other abrasive materials
example: removing grouting joints between wall tiles for
repair work, cutting openings in tiles, gypsum boards or
plastic
Rasping and sanding on hard surfaces;
wood, abrasive materials
example: removing mortar or tile adhesive (e.g. when
replacing damaged tiles)
Carpets, coverings
Scraping on hard surfaces;
example: removing carpet and tile adhesive
Insulation material, insulation
Cutting soft materials
panels, floor panels, sound in-
sulation panels, cardboard,
carpet, rubber, leather
– With segment saw blades ACZ 100 .. with a diameter of
100 mm: 14 mm, 16 mm, 18 mm and 20 mm cutting
depths (see indication on the depth stop in smaller font
and brackets).
Insert the appropriate segment saw blade for the desired cut-
ting depth. Slide the depth stop 11 from the tool holder 5 in
the direction of the application tool until you can rotate it free-
ly. Rotate the depth stop 11 so that the desired cutting depth
is above the section of the saw blade, which will be used to
saw. Slide the depth stop 11 once again to the stop onto the
gear head of the application tool.
For all other cutting depths and when working with other appli-
cation tools, remove the depth stop 11. For this, remove the
application tool and pull the depth stop from the gear head.
Mounting/Replacing a Sanding Sheet on the Sanding Plate
The sanding plate 9 is fitted with Velcro backing for quick and
easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet 10, free the Velcro back-
ing of the sanding plate 9 from any debris by tapping against
it in order to enable optimum adhesion.
Position the sanding sheet 10 flush alongside one edge of the
sanding plate 9, then lay the sanding sheet onto the sanding
plate and press firmly.
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
To remove the sanding sheet 10, grasp it at one of the tips and
pull it off from the sanding plate 9.
You can use all sanding sheets, fleece pads/polishing cloth
pads of the Delta 93 mm series of Bosch accessory program.
Sanding accessories, such as fleece pads/polishing cloth
pads, are attached to the sanding plate in the same manner.
Bosch Power Tools
Publicité
Table des Matières
