Numatic TTB 1840 Mode D'emploi page 45

PROBLEM
Machine will not operate
Vacuum will not operate
Poor water pick-up
No brush / scrub function
Little or no water flow
Machine just 'stops' while
operating
Specifications
Brush Motor Vac Motor
400W 24V 300W
Area Performance Fluid Flow
per battery pack (Tap at 45')
0.35 LPM
1050m
2
(60 mins)
Recommended Spare Parts - TTB-1840
606105 400MM SCRUBBING BRUSH (MDA-21)
606400 360MM PADLOC DRIVE BOARD
606260 TTB-1840 BATTERY PACK (BOXED)
606266 TTB-1840 BATTERY & CHARGER PACK (UK)
606267 TTB-1840 BATTERY & CHARGER PACK (EURO)
606268 TTB-1840 BATTERY & CHARGER PACK (SWISS)
606269 TTB-1840 BATTERY & CHARGER PACK (CSA)
606270 TTB-1840 BATTERY & CHARGER PACK
(SOUTH AFRICA)
606271 TTB-1840 BATTERY & CHARGER PACK (AUS)
606272 TTB-1840 CHARGER PACK (UK)
606273 TTB-1840 CHARGER PACK (EURO)
606274 TTB-1840 CHARGER PACK (SWISS)
606275 TTB-1840 CHARGER PACK (CSA)
606276 TTB-1840 CHARGER PACK (SOUTH AFRICA)
606277 TTB-1840 CHARGER PACK (AUS)
Model TTB-1840
CAUSE
Missing or blown fuses
Battery not connected
Low battery charge
Vacuum not turned on
Waste-water tank full
Clogged / blocked vacuum hose
Loose hose connections
Debris basket filter clogged / blocked
Separator filter clogged / blocked
Poor separator seal
Damaged separator seal
Damaged / split vacuum hose
Damaged floor-tool blades
Low battery charge
No brushes fitted
Brush overloaded
Clean-water tank empty
Clean-water tank filter blocked / clogged
Incorrect water flow setting
To much load on the brush system
Blown fuse in Battery pack
Brush Pad
Sizes sizes
400mm 360mm
Brush / Pad
Speed
Pressure
27.4/ Hi-150 rpm
26.2 g/cm Lo-130rpm
2
Trouble-Shooting
Protection
Weight
Class per battery pack
52 Kg IPX4
Recharge Cleaning
time Speed
6 hrs 0-4.2Kph
606261 TTB-1840 REPLACEMENT BLADE SET
303985 TTB-1840 FILLER CAP
ASSEMBLY
237268 FILLER CAP LID
237232 TTB-1840 SEPERATOR FILTER
237260 TTB-1840 GRIT BASKET
231054 TTB-1840 SUCTION HOSE
213055 TTB-1840 VAC HOSE
208471 CONSTANT TENSION CLIP
303997 TTB-1840 DUMP-HOSE
ASSEMBLY
208448 TANK DRAIN CAP
208526 REPLACEMENT 40AMP FUSE
208455 M5 KNOB (BLACK)
208537 CONSTANT TENSION CLIP (VAC HOSE)
45
SOLUTION
Fit or replace fuse (page 40)
Connect battery (page 20)
Charge batteries (page 42)
Turn on vacuum (page 32)
Empty waste-water tank (page 34)
Remove and clean (page 36)
Push tight connections (page 36)
Remove and clean (page 36)
Remove and clean (Page 36)
Clean and refit (page 36)
Renew (contact service dept)
Renew (contact service dept)
Renew (contact service dept)
Recharge batteries (page 42)
Check and fit (page 22)
Reset machine (page 32)
Fill clean-water tank (page 24)
Remove and clean (36)
Adjust tap as desired (Page 26)
Reset the machine and decrease the brush
load to best suit the floor type (page 32)
Replace 40 Amp fuse (page 40)
Run Time
Hi - 35 mins
2 x 12V (24V) 18Ahr
Lo - 45 mins
Hand Arm
Noise
Vibration
Hi-70.3 dB(A)
0.6 m/s
2
Lo-68.2 dB(A)
Power
Size
850mmx
1132mmx
520mm