Machine Use; Restrictions On Use - T.O.M TST254A Manuel D'utilisation

MaCHinE iDEnTifiCaTiOn anD iLLUsTraTiOns ( PaGEs 7, 8, 9, 10 )
1. Saw table 9. bevel adjustment and locking handle
2. blade guard 10. base made up of 4 cross-pieces
3. Push stick 11. On/off switch
4. Saw blade 12. Rip fence locking lever
5. Riving knife 13. Extraction hose
6. Table insert 14. Mitre fence
7. Rip fence 15. blade guard wing screw
16. dust extraction nozzle
8. blade height
17. Riving knife fastening screw
adjustment wheel
18. Rip fence rail
sPECifiCaTiOns
Power 1600 w
Voltage 230 V ~ 50 hz
blade diameter 254 mm
bore 30 mm
Rotation speed 4800 rpm
Cutting height at 90° 70 mm
Cutting height at 45° 60 mm
Table size 595 x 440 mm
Table extension 595 x 944 mm
Saw height 890 mm
Net weight 31 kg
gross weight 35 kg

MaCHinE UsE

This machine has been designed exclusively for rip cutting and cross cutting wood that is up to 70 mm thick. For safety reasons, this ma-
chine must be secured to the ground when in use, as shown in this manual.

rEsTriCTiOns On UsE

dO NOT cut wood thicknesses over 70 mm.
dO NOT cut metal, stone, rubber, plastic, plaster, glass wool, etc.
dO NOT cut logs or pieces of wood with irregular shapes.
dO NOT use it for grooving or moulding.
DO NOT fit other tools or different blades.
dO NOT use as a portable or unsecured machine.
dO NOT modify the machine, its safety devices, guards or switches.
dO NOT use the machine in any way without its guards or required adjustments.
dO NOT use hSS blades.
dO NOT use this saw for making stopped grooves.
reMove the transport proteCtion Before use.
iMportant
Refer to the paragraph "Assembling the base" to remove the transport protection located on the saw motor.
assEMBLinG THE BasE
1. Turn the saw over and place it on the ground as shown in Fig.17.
2. Lightly fasten the 4 legs (29) to the saw using the hex head screws and the nuts.
3. Next, screw the 4 cross-pieces (30) with the hex head screws and the nuts provided Fig.17.
4. you may now attach the rubber pads (31) to the ends of the four legs.
5. before continuing, remove the lower protection plate by unscrewing the 4 screws.
6. Next use the blade adjustment handle to tilt the saw and lift off the transport protection.
7. Re-attach the lower protection plate by re-fastening the 4 screws.
8. Turn over the saw and place it on the ground upon its base.
9. Then fully re-fasten all the screws and nuts on the base as shown in Fig.18.
assEMBLinG THE siDE TaBLE ExTEnsiOns
1. Lightly attach the side table extensions (26) Fig.1 to the saw table (1) using the screws and corresponding nuts Fig.19.
2. Lightly fasten the support bars (27) Fig.1 to the saw frame and to the side extensions.
3. Adjust the table extensions horizontally in relation to the surface of the saw table (1).
4. Then fully tighten all screws as shown in Fig.20.
19. Rip fence scale
20. Rip fence section
21. Rip fence knurled screw
22. Section slot
23. Section slot
24. Mitre fence adjustment
screw
25. Table insert fastening screw
26. Side table extension
27. Four side extension support bars
28. Table guide slide slots
29. Legs of the saw
30. base cross-pieces
31. Rubber pads
32. blade guard fastening hole
21