Publicité
Workstation Use Requirements
Intended for use in a garage.
Ƀ
Maximum weight limit is 50 lbs (22.7 kg) for each shelf.
Ƀ
Maximum weight limit is 200 lbs (90.7 kg) for the workstation.
Ƀ
Unpack Workstation Parts
Remove and verify the contents. Contents include an
Ƀ
Allen
®
† wrench, and the parts and fasteners shown in "Parts."
Dispose of/recycle all packaging materials.
Ƀ
Gather the required tools before starting installation.
Ƀ
Tools Needed:
Ƀ
1/2" wrench
Ƀ
1/4" wrench
Ƀ
Pliers
Ƀ
Tape measure
Ƀ
1.
Workstation Sides and Bottom
P1
P2
P1. Left Side Panel
P2. Bottom Panel
F1. 5/16" Allen-head bolt
F2. 5/16" Flange Nut
With the cable bracket edge to the top, place left side panel
(P1) on a flat, firm surface. With the electrical cord access to
the back, insert the bottom panel (P2) between the edges of
left side panel (P1).
NOTE: To create an opening for electrical cords, remove the
center of the plastic grommet. Insert electrical cords and
snap the center back into place.
Align the holes in the left side panel (P1) with the holes in the
back and side edges of the bottom panel (P2).
NOTE: There will be a space between the top edge of the left
side panel (P1) and the front edge of the bottom panel (P2).
With the cable bracket edge to the top, position right side
panel (P3) so that the bottom panel (P2) is between the edges
of right side panel (P3).
Align the holes in the right side panel (P3) with the holes in the
back and side edges of the bottom panel (P2).
NOTE: There will be a space between the top edge of the
right side panel (P3) and the front edge of the workstation
bottom panel (P2).
Use four Allen-head bolts (F1) and four flange nuts (F2) per
side to attach the bottom panel (P2) to both the side panels
(P1 and P3) on Gladiator
GearWall
®
as shown. Do not fully tighten.
NOTE: The workstation can be directly mounted to the wall.
Allen is a registered trademark of Apex Brands, Inc.
†®
ASSEMBLY INSTRUCTIONS
F1
A
F2
P3
P1
P2
F1
P3
P2
P1. Left Side Panel
P2. Bottom Panel
P3. Right Side Panel
F1. 5/16" Allen-head bolt
F2. 5/16" Flange Nut
A. Cable Bracket
or GearTrack
systems
®
®
Tools Supplied:
3/16" Allen wrench
Ƀ
IMPORTANT: Two people may be required to complete the
assembly.
Use two or more people to move shelving.
Failure to do so can result in back or other injury.
2.
Workstation Shelf
F2
F1
F1
F2
P1. Left Side Panel
P2. Bottom Panel
P3. Right Side Panel
P4. Shelf
F1. 5/16" Allen-head bolt
F2. 5/16" Flange Nut
Align the holes in the ends of the shelf (P4) with the holes in
both the side panels (P1 and P3). Insert two 5/16"
Allen-head bolts (F1) through each side panel (P1 and P3)
and into the shelf (P4). Fasten with two 5/16" flange nuts (F2).
Insert another two 5/16" Allen-head bolts (F1) through the
flange under the shelf (P4) and into each side panel (P1 and
P3).
WARNING
Excessive Weight Hazard
F2
P4
F1
P4
F1
F2
P1
P2
P3
F1
P3
5
Publicité
