Publicité
6. Treatment and Storage
The rubber coating on the boat surface will not tolerate
long-term exposure to oil, petrol, toluene, acetone, kerose-
ne and similar solvents. Whenever it gets stained and be-
fore storing it, wash the boat with lukewarm water with an
addition of soap or detergent. Thorough rinsing is necessary
after use in seawater. It is advisable to check the condition
of the inflation and relief valves. If a valve is leaky, you can
use a special valve wrench to screw out the valve body and
clean the diaphragm using a stream of compressed air or
water. Before storing the boat, you are recommended to treat
the boat surface with a boat surface treatment agent, which
has a cleaning effect, impregnates the material against con-
tinued contamination, and may even produce a UV protecti-
ve filter. Never use silicone-containing agents for treating the
boat. Store the cleaned and dried boat in a dark, dry place
at a temperature of (15–35) °C/(59–95) °F, at least 1.5 m/ 5 ft.
from any radiant heat source and out of the reach of rodents.
When stored for a long time, the boat should be inflated for
24 hours from time to time to prevent damage. You are reco-
mmended to have a servicing check made on the boat by the
manufacturer or an authorized workshop at least once every
two to three years.
The boat life can be extended by careful treatment and
maintenance.
7. Guarantee Conditions-limited warranty
The guarantee period is 24 months and is calculated from
the date of sale. The producer provides cost-free repairs or
replacement of faulty components for material faults or pro-
duction faults. The warranty does not cover damage to air
chambers due to higher pressure than the required opera-
tional pressure !!!
To claim the warranty, contact the distributor.
Detailed information can be found at the address:
www.gumotexboats.com
www.gumotexusa.com
8. Boat Repairing
You can easily repair a damaged boat yourselves by means
of the accompanying gluing set.
Gluing:
• mark out the damaged area on the boat and choose
an appropriately sized patch;
• the surfaces of both patch and place to be glued must be
clean, dry and without traces of old glue;
• we recommend degreasing both surfaces with acetone in
order to achieve a perfect bond;
• spread a thin layer of glue on both surfaces to be glued
and repeat this step once the first layer has dried;
• after the second layer has dried, press the patch firmly on
the damaged place, weigh down or use a rolling pin on
a flat surface.
For minor repairs (punctures), it is possible to re-inflate the boat
and continue using it after waiting for approx. 30 minutes;
after more serious repairs, you should wait for 24 hours
before using the repaired boat. Complicated repairs should
be performed by the manufacturer or at authorized service sta-
tions.
To claim post-warranty repairs, contact the distributor.
12
9. Product Disposal Method
The boat rudder is disposed of at municipal landfills or using
the best available technology.
Recycle the user´s manual or dispose of it with municipal
waste.
10. Packaging Disposal Method
Cardboard – recycle as the indicated symbol directs.
PE bubble foil – recycle as the indicated symbol directs.
11. Type Parameters Tag
Each boat is provided with its own Type Parameters Tag which
displays the most important technical parameters. Please follow
these values. Above all, do not overload the boat and maintain
the recommended maximum pressures in the air chambers.
PULSAR 380 N
EN ISO
6185-1, I
0,025
=
0,25
bar
3,75
PSI
7
0
+
+
GUMOTEX Coating, s.r.o., Mládežnická
690 02
Břeclav. Made in Czech Republic.
PULSAR 380 NEX
EN ISO
6185-1, I
0,025
=
0,25
bar
3,75
PSI
7
0
+
+
GUMOTEX Coating, s.r.o., Mládežnická
690 02
Břeclav. Made in Czech Republic.
PULSAR 420 N
EN ISO
6185-1, I
0,025
=
0,25
bar
3,75
PSI
8
0
+
+
GUMOTEX Coating, s.r.o., Mládežnická
690 02
Břeclav. Made in Czech Republic.
PULSAR 420 NEX
EN ISO
6185-1, I
0,025
=
0,25
bar
3,75
PSI
8
0
+
+
GUMOTEX Coating, s.r.o., Mládežnická
690 02
Břeclav. Made in Czech Republic.
D
MP
a
WW
5
650 kg
MAX.
=
1433 lbs
3062/3a,
655
D
MP
a
WW
5
650 kg
MAX.
=
1433 lbs
3062/3a,
663
D
MP
a
5
WW
800 kg
MAX.
=
1764 lbs
3062/3a,
656
D
a
MP
5
WW
800 kg
MAX.
=
1764 lbs
3062/3a,
664
Publicité
