Peg-Perego Sdraietta Melodia Notice D'emploi page 12

_ NOTICE: THIS ARTICLE MEETS OR EXCEEDS ALL REQUIREMENTS COVERED IN
ASTM F2050 STANDARD AND LATEST REVISIONS.
WEEE DIRECTIVE (EU only)
_ At the end of its useful life, this product is classed as Waste Electrical and Electronic Equipment (WEEE) and
must therefore not be disposed of as urban waste but instead must be taken to a designated separated
waste collection facility.
_ Take the refuse to the relevant designated collection facility.
_ The presence of dangerous substances contained in the electrical components of this product represents
a potential source of danger for human health and for the environment if the product is not correctly
disposed of.
_ The barred dustbin indicates that the product must be subject to sorted waste collection.
INSTRUCTIONS
1 OPENING: to open the baby rocker, rotate the frame bars forwards until they click (fig_a) and release the sun
canopy from the handle (fig_b).
2 ASSEMBLING THE BABY ROCKER: to fit the handle, move the backrest into the vertical position (see point 4).
Slot the handle into the tubes (fig_a) and fasten it in place with a screwdriver, ensuring that the crosshead
screw is on the outside of the handle (fig_b). Tighten well and periodically check that it is fixed properly.
3 ADJUSTING THE HANDLE: the handle can be set in 3 different positions. Push the two levers (fig_a) in the
direction of the arrows and at the same time rotate the handle into the required position (fig_b).
The transport position is number 1.
4 ADJUSTING THE BACKREST: The backrest can be set in 3 different positions. Rotate lever 1 outwards (leaving
it in the open position) (fig_a), rotate lever 2 outwards and at the same time adjust the backrest (fig_b).
Once in the selected position, remember to close lever 1 again.
5 ADJUSTING THE REAR LEDGE: the rear ledge can be set at two different heights. To raise it, pull the two
levers outwards from both sides and at the same time push the tabs upwards (fig_a). Rear ledge raised
(fig_b).
6 SAFETY BELT: thread the safety belt through the crotch strap and engage the buckle until it clicks (fig_a). To
release the safety belt, press the two sides of the buckle and simultaneously pull the waist strap outwards
(fig_b).
7 STAND: the base of the baby rocker can be rocking (fig_a) or stable. To stop it from rocking, rotate the
stabilizer stand outwards (fig_b).
8 SUN CANOPY: the baby rocker has a sun canopy that can be placed in different positions. It attaches to the
handle at any height.
9 PLAY BAR: attach the play bar (fig_a). It can be fitted to the front of the frame (fig_b) or to the handle (fig_c),
depending on the position of the backrest.
10 The play bar can be detached on one side only, and rotated externally. To make the cow moo, press its
hooves (fig_b).
11 SOUND MODULE: batteries are NOT included. The sound module requires 2 "penlight" type AA 1.5V
batteries. Use a screwdriver to unscrew the battery compartment cover (fig_a), insert the batteries. (fig_b),
and then screw the cover back on. The sound module has 2 volume settings and 8 music options (fig_c).
A: To switch on the sound module and to adjust the volume, move the button upwards.
B: 4 playful tunes.
C: 4 soothing tunes.
To change the music, push the relevant buttons.
12 BOOSTER CUSHION: the baby rocker comes with a booster cushion for newborn infants which can be
removed when the child gets bigger. To remove the booster, unthread the crotch strap.
13 CLOSING: to close the baby rocker (fig_a), put the handle and the back rest in the lowest position, press
button A on both sides at the same time and pull together as in the figure. Before moving the closed baby
rocker, put the elastic loop around the fastener (fig_b). When closed, the baby rocker is extremely compact
and takes up very little space (fig_c).
14 REMOVING COVERS: to remove the cover of the baby rocker, detach the Velcro (fig_a), slip off the sound
module cover by moving it towards the front (fig_b), then disconnect the sound module connector by
detaching the two jacks (fig_c).
15 Slip the cover side loop off the frame tubes (fig_a), unbutton the back of the backrest (fig_b) and slide the
- 12 -