Publicité
Les langues disponibles
Les langues disponibles
Please note that our equipment has not been designed for use
in commercial, trade or industrial applications. Our warranty
will be voided if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.
5. Safety information
• Use the universal tool stand only in conjunction with suitable
electric power tools!
• Check the universal tool stand for damage each
time before use. Electric power tools shall not be mount-
ed or operated on damaged support arms / crossbars.
• Electric power tools must be bolted to the sup-
port arms / crossbars and be secured on the uni-
versal tool stand!
• Always ensure the universal tool stand is secure
when setting it up.
• Always ensure that you assume a natural and safe standing
position when working.
• Do not overload the universal tool stand! Do not
use the universal tool stand for purposes for which it is not
intended.
• To prevent the universal tool stand from tipping over, make
sure that the load does not extend laterally beyond the uni-
versal tool stand.
• Modifications or unauthorised changes to the universal tool
stand as well as the use of unapproved parts is forbidden.
• All parts of the universal tool stand, in particular the safety
devices, must be correctly mounted in order to guarantee
trouble-free operation.
• Keep the universal tool stand out of reach of chil-
dren. Store the device in a location that is inaccessible to
unauthorised persons and children.
m Attention!
When using electric power tools, in conjunction with the univer-
sal tool stand, the respective machine-specific safety measures
must be implemented as protection against electric shock, and
the risk of injury or fire.
Read all of the instructions for the electric power tool that you
intend to mount and operate before using the tool.
Safety instructions for the electric device mounted must likewise
be observed.
Store these safety instructions safely.
Observe all safety instructions. If you disregard the safety in-
structions, you endanger yourself and others.
6. Technical data
Dimensions ......................1000 - 1650 x 580 x 810 - 910 mm
Table height .................................................................... 750 mm
Height of the side expansions .............................810 - 910 mm
Spacing of the supports min./max. ................ 1000 - 1650
Max. permissible payload ............................................... 200 kg
Weight ............................................................... approx. 13.3 kg
7. Before starting the equipment
Check the device for transport damage. Immediately report
any damage to the transport company that delivered the de-
vice.
• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the packaging
and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport damage.
• If possible, store the packaging until the warranty period has
expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
8. Attachment and operation
The universal tool stand is largely assembled and you need
only fit the handgrips and the workpiece supports as follows:
8.1 Erecting the universal tool stand (fig. 3 - 4)
Place the universal tool stand (A) on the floor or on a work-
bench such that the frame legs (A.1) point upwards.
Press the spring pin (M) and fold out the frame leg.
Once the spring pin (M) latches into the intended position (L),
the frame leg is locked.
Repeat this process for the other frame legs.
Set the universal tool stand down on its feet.
8.2 Mounting support arms (fig. 5)
Fit the support arms (B) to the frame bed (A) by pulling the
locking lever (B.3) upwards to unlock it and then latching the
arm into place on the frame base, firstly on the front side (B.2).
Lower the rear side onto the bed and fasten the support arm
in place on the frame bed by pressing the locking lever (B.3).
Disassembly is carried out in reverse order.
8.3 Fitting the workpiece supports (fig. 6 - 7)
Insert the workpiece support (D) into the receiver (N) of the
frame bed and fasten in place with the star-grip screws (K).
The width and height of the workpiece supports can be ad-
justed with the star-grip screws (J, K). (fig. 7)
8.4 Fastening your tabletop machine (fig. 8)
Different tabletop machines can be fastened to your universal
tool stand by adjusting the support arms (B) to the spacing of
the mounting holes on your machine.
• Place your tabletop machine (e.g. mitre saw) on the support
mm
arms (B).
• Fasten the tabletop machine with 4 hexagonal screws (F), 4
washers (G), 4 spring washers (H) and 4 hexagonal nuts (I)
on each of the support arms.
• Tighten the screws after assembly.
GB/IE/NI
3
Publicité
