FMS 90MM AVANTI Manuel D'utilisation page 15

User Manual of Brushless Speed Controller
2). (With a battery connected to your ESC), after connected a LED program box to the ESC, you need to disconnect the battery
first and then reconnect it to the ESC to enter the programming mode, check and set parameters.
The portable program box is an optional accessory applicable for field use. Its friendly interface makes the ESC programming easy
and quick. Connect a battery to your ESC after connecting a LED program box to the ESC, all programmable items will show up a
few seconds later. You can select the item you want to program and the setting you want to choose via "ITEM" & "VALUE" buttons
on the program box, and then press the "OK" button to save all new settings to your ESC.
Attention! You need to power your ESC off and then on after adjusting parameters. Otherwise, new parameters won't take effect.
II. Program your ESC with the Transmitter
It consists of 4 steps: Enter the programming → Select parameter items → Select parameter values → Exit the programming
1.Enter the Programming
Turn on the transmitter, move the throttle stick to the top position, and connect a battery to the ESC, 2 seconds later, the motor will
beep "B-B-" first, then emit 5 seconds later to indicate that you are in the ESC programming mode.
2.Select Parameter Items
After entering the programming, you'll hear the following 12 kinds of beeps circularly. Move the throttle stick to the bottom position
within 3 seconds after you hear some kind of beeps, you'll enter the corresponding parameter item.
1. "B-" Brake Type
2. "B-B-" Brake Force
3. "B-B-B-" Voltage Cutoff Type (3 Short Bs）
4. "B-B-B-B-" LiPo Cells
5. "B——" Cutoff Voltage
6. "B——B-" Start-up Mode
Note: A long "B——" equals to 5 short "B-", so a long "B——" and a short "B-" represent the 6th item in "Select Parameter Items".
III. Select Parameter Values
The motor will beep different kinds of beeps circularly, move the throttle stick to the top position after you hear some kind of beeps
will get you to the corresponding parameter value, then you'll hear the motor emit "" to indicate the value is saved, then get back to
"Select Parameter Items" and continue to select other parameter items that you want to adjust.
Values (Bs)
Items
Brake Type
Brake Force
Voltage Cutoff Type
LiPo Cells
Cutoff Voltage
Start-up Mode
Timing
Acitve Freewheeling
Search Mode
INote: Those values marked with * in the form below are the factory default settings.
VI. Exit the Programming
Move the throttle stick to the bottom position within 3 seconds after you hear "Two long and One short beeps" (emitting from the
motor) can get you exit the programming mode. The motor beeps "Number" beeps to indicate the number of LiPo cells you have
plugged in, and then a long beep to indicate the power system is ready to go.
(1 Short B) 7. "B——B-B-"
(2 Short Bs) 8. "B——B-B-B-"
9. "B——B-B-B-B-" Search Mode
(4 Short Bs) 10. "B——B——"
(1 Long B) 11. "B——B——B-"
(1 Long B & 1 Short B)
B- B-B-
1 2
Disabled Normal
*Low Medium
*Soft Hard
*Auto Calc. 3S
Low
Disabled
*Normal Soft
Low *Medium
*On Off
*Off 5min
15
Timing
Active Freewheeling (1 Long B & 3 Short Bs)
Factory Reset
Exit
B - B - B - B-B-B-B-
3 4
*Reverse Linear Reverse
High
4S 5S
*Medium
High
Very Soft
High
10min 15min
(1 Long B & 2 Short Bs)
(1 Long B & 4 Short Bs)
(2 Long Bs)
(2 Long Bs & 1 Short B)
B--
5
6S