BOMANN 666029 Mode D'emploi page 47

Operation
CAUTION:
Before switching of the beer dispenser, always ensure
that no 5 litre party keg is present in the dispenser as the
beer in the keg becomes warm and is no longer fresh.
Close the lid of the appliance. It must audibly snap.
Electric Connection
1. Ensure that your mains power corresponds with the
specifications of the appliance. The specifications are
printed on the type label.
2. Connect the mains cable to a properly installed and
earthed wall outlet.
Turning the Appliance On / Off
• Set the switch to the " I " position to turn the appliance on.
• The appliance is turned off when in the " " position.
Temperature Adjustment
NOTE:
The appliance saves the most recently set cooling tem-
perature while switching it off.
After switching the appliance on again, the display will show
the current temperature of the inserted beer keg and the
last set cooling temperature.
• You can choose a cooling temperature ranging from 2 °C
to 12 °C.
• In order to display the set temperature, you may briefly
press the or button.
• Press and hold the or
ature setting.
Pressure Regulator for Carbon Dioxide
(Exception: Heineken kegs)
Use the pressure regulator to select the appropriate pres-
sure for your beer. As different beer varieties are carbonated
to a differing extent, different pressures (saturation pres-
sure) are required to ensure the quality of the respective
beer. If a beer is dispensed with insufficient pressure, for
example, it can make the beer taste flat, whilst too much
pressure can make it too fizzy. If the beer should be too
fizzy or flat, simply adjust the pressure accordingly. To be
noted is that the CO content in the beer initially changes
2
over the course of time.
NOTE:
Make sure the pressure regulator is always in the " "
position when
• the beer drawing procedure is interrupted.
• you replace the CO cartridge or the keg.
2
• In case you can no longer draw beer, even though there
is still beer in the keg, or foaming requires too much
time, slowly turn the pressure regulator towards " " for
BZ6029CB_IM
button to adjust the temper-
5 seconds. Then set the pressure regulator back to the
" " position.
Drawing Beer
1. Preparing glasses
Wash the glasses in hot water with a small amount of
washing / up liquid. Rinse the glasses thoroughly each
time before dispensing with cold, clear water.
Ensure that all grease and residues are removed com-
pletely to avoid impairing foam formation.
NOTE:
The best results can be achieved by using glasses
exclusively for beer to ensure that no residues from fat
containing drinks (e. g. milk) are present.
2. Dispensing beer
Hold the glass under the beer tap at an angle. The tip
of the outlet tube should not come into contact with the
glass as this can impair the foam formation.
NOTE:
The foam produced when dispensing beer can be
influenced by changing the angle of the glass.
Pull down the tap handle in one motion.
NOTE:
If the tap is only partly open, the beer may foam exces-
sively as it is not able to flow out freely.
Allow the beer to run down the inside of the glass and
slowly straighten the glass while dispensing until it is
upright towards the end.
When the foam reaches the rim of the glass, close the
beer tap by pushing back the beer tap handle.
Place the glass on the drip plate and wait until the foam
has settled. Ensure that the glass is not located directly
under the beer tap so that no drops fall into the bear
foam.
Repeat the dispensing process until the beer and foam
are in the correct proportion. This is the case when the
head is about two finger's breadth high and slightly over
the rim of the glass.
Replacing the Carbon Dioxide (CO
(Exception: Heineken kegs)
WARNING for frostbite:
• Do not remove the CO cartridge before it is com-
2
pletely emptied.
• A residual amount of CO may still be present in the
2
cartridge, which suddenly empties and results in the
formation of ice.
Once no beer can be drawn, even though the pressure
regulator is in the " " position and there is still beer in the
keg, replace the CO cartridge.
2
1. Switch off the appliance.
2. Disconnect the mains plug from the socket.
) Cartridge
2
47
07.03.19