Télécharger Imprimer la page

Amica KM 5011 Notice D'utilisation page 5

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 12
This appliance generates heat.
The kettle switches off automatically when water boils. You can
switch the kettle off before water boils using a switch. When the
kettle switches off automatically (or when it was switched off man-
ually), it may take some time (approximately 15 ­ 20 seconds to cool
down) to be ready for re­use.
The kettle must only be used with the supplied base.
Do not touch the surface marked with this symbol. Do not
touch the surfaces during or after operation of the appliance.
These surfaces are hot.
Unplug the kettle from the power outlet and wait until it cools down
before cleaning.
When boiling the water, parts of the kettle made of stainless steel
become very hot.
Do not switch on the kettle without an adequate amount of water
(level marked as "min" on the scale).
Do not leave the kettle unattended, and when not completely
cooled down.
Use only the handle to move the kettle, other external parts may
be hot.
Use the appliance on a flat and stable surface.
Make sure that the voltage indicated on the nameplate corresponds
to that of your home electrical mains. Alternating current must be
used, typically marked ~.
This appliance is intended for use at home or in facilities, such as
kitchen for employees; in shops, offices and other working environ-
ments, use by the customers of hotels, motels and other residential
facilities, in rural residential buildings, in the accommodation facil-
ities.
SPECIFICATION:
Power specification:
Power rating:
Capacity:
OPERATE THE APPLIANCE:
Before using the appliance for consumption, boil clean water in
it several times by filling the kettle to the maximum position. Use
fresh, cold water for each boil cycle.
USE:
Place the base on a solid and level surface.
Remove the kettle from the base, press the button on the handle to
open the lid and fill the kettle with water as needed between the
min­max level. Close the lid and put the kettle back on the base.
Use the buttons to set the desired programme. When a boil cycle is
completed, the appliance will turn off or maintain the temperature.
Use the hot water from the kettle and put the appliance back on
its base.
Note! Only use the kettle with its lid closed.
FEATURES AND COMPONENTS:
Programme 1: Boil water (100°C)
Press
to start heating the water (one indicator above the display
is on). When the set temperature is reached, you will hear a beep
and the appliance will turn off.
Programme 2: Heat water to a preset temperature (40°C – 100°C)
Press
several times to select the temperature, then press
to start heating the water (one indicator above the display is on).
When the set temperature is reached, you will hear a beep and the
appliance will turn off.
Programme 3: Heat and maintain the temperature (40°C – 90°C)
Press
several times to select the temperature. Then press
start heating the water to the set temperature and then maintain
the temperature for 1 hour (two indicators above the display are
on). When the time elapses, you will hear a beep and the appliance
will turn off.
Programme 4: Boil the water and maintain the temperature (40°C
– 90°C)
Press
several times to select the temperature. Press
boil the water to 100°C, and then to maintain the previously set
temperature for 1 hour (three indicators above the display are on).
When the time elapses, you will hear a beep and the appliance will
AC 220­240V / 50­60Hz
1850­2200W
1.7l
twice to
turn off.
If you accidentally turn on the kettle without water, the safety de-
vice will operate, and the kettle will turn off automatically after
about 17 seconds. You will be able to use the kettle again when the
heating element has cooled down and you fill the kettle with water.
CLEANING:
Before cleaning, always unplug the appliance from the wall outlet
and allow it to cool down completely.
1.
Do not immerse the kettle, cord and power base in water and
protect against contact with moisture.
2.
Wipe the outside of the kettle with a damp cloth or mild
cleaning agent; never use any poisonous cleaning agents.
3.
Remember to clean the filter regularly. To facilitate cleaning,
remove the filter by pressing the filter tab inside the kettle,
and reinstall it after cleaning.
NOTE: To prevent matting, do not use any abrasive cleaners, harsh
chemicals, steel or wood to clean the outside of the kettle.
4.
When the kettle is not in use and in storage, you can wind the
power cord under the kettle base.
DESCALE YOUR APPLIANCE
If the appliance switches off before the water boils, it means des-
caling is required. Descale your kettle periodically, as minerals dis-
solved in the tap water can form limescale on the bottom of the
kettle, which reduces the water heating efficiency. You can use a
commercially available descaler and follow the instructions on its
packaging. You can also use white vinegar and follow the instruc-
tions below.
1.
Fill the kettle with 3 cups of white vinegar and then add water
until it completely covers the limescale. Leave the solution in
the kettle overnight.
2.
Then pour the mixture out of the kettle, fill the kettle with
clean water to the maximum level, bring it to a boil and then
pour out the water. Repeat several times until the smell of
vinegar disappears. Any limescale residue inside the spout
can be removed by wiping with a damp cloth.
to
5
EN

Publicité

loading