Hercules FKS 2201 Mode D'emploi page 15

Anleitung FKS 2201_SPK7:Anleitung FKS 2200 SPK 7
blade guard (2).
A suitable extractor system has to be connected
to the outlet of the extractor adapter (14).
To remove the saw blade guard, proceed in
reverse order.
Important!
The guard hood (2) must always be lowered
over the workpiece before you begin to cut.
7.4. Setting the splitter (Fig. 12/13/14/15)
Important! Pull out the power plug.
Set the blade (4) to max. cutting depth, move to
0° position and lock in place (see 8.4).
Remove the saw blade guard (see 7.3).
Take out the table insert (6) (see 7.5).
Slacken the fixing screw (38).
7.4.1 Setting for maximum cuts
Push up the splitter (5) until the gap between the
saw table (1) and the upper edge of the splitter
(5) is at its maximum.
The maximum distance between the saw blade
(4) and the splitter (5) is 8mm.
Re-tighten the nut (38) and mount the table
insert.
7.5 Dismantling the sliding table and opening the
chip box (Fig. 12, 13)
To dismantle the sliding table (3), pull the sliding
table (3) forward until the latching hook (10)
becomes visible.
Press down on the locking hook (10) with one
hand and at the same time use the other hand to
pull the sliding table (3) forward and out of the
guide (24)!
To open the chip box (17), remove the two
screws (b) and flip open the chip box. Tip: You
will find it easier to remove the screws (b) if you
set an angle of approx. 45° (see 8.5)
To assemble, proceed in reverse order.
7.6. Changing the saw blade (Abb. 16)
Important! Pull out the power plug first.
Set the saw blade (4) to max. cutting depth (see
8.2)
Take off the saw blade guard (2) (see 7.3).
Dismantle the saw table (see 7.5).
Open the lower chip box (see 7.5)
Place the counterholder (41) on the saw blade
flange.
Using the wrench (40), turn out the screw (42) in
the running direction of the saw blade.
Remove the saw blade (4) from the inner flange
and pull out in an upwards direction.
Clean the blade flange thoroughly before fitting
the new blade.
16.11.2006
Mount and fasten the new saw blade in reverse
order. Important! Note the running direction.
The cutting angle of the teeth must point in
running direction, i.e. forwards (see the
arrow on the chip box).
Refit and set the splitter (5) and the saw blade
guard (2) (see 7.4., 7.5.)
Check to make sure that all safety devices are
properly mounted and in good working condition
before you begin working with the saw again.
8. Using the saw
8.1. ON/OFF switch (Fig. 10)
To turn the saw on, press the green button "I" .
Wait for the blade to reach its maximum speed
of rotation before commencing with the cut.
To turn the machine off again, press the red
button "0".
8.2. Cutting depth (Fig. 17)
Turn the hand crank (8) to set the blade (4) to
the required cutting depth.
Turn anti-clockwise: larger cutting depth
Turn clockwise: smaller cutting depth
8.3. Parallel stop
8.3.1. Stop height (Fig. 19/20)
The parallel stop (6) supplied with the bench-
type circular saw has two different guide faces.
For thick material you must use the stop rail (43)
as shown in Fig. 19, for thin material you must
use the stop rail as shown in Fig.20.
8.3.2. Cutting width (Fig. 19/20)
The parallel stop (6) has to be used when
making longitudinal cuts in wooden workpieces.
The parallel stop (6) should be mounted on the
right-hand side of the saw blade (4).
The parallel stop (6) must be pushed into the
guide (23) from the outside.
Set the parallel stop (6) to the required
dimension and fix it in place with the eccentric
lever (21).
8.3.3. Setting the stop length (Fig. 21)
The stop rail (43) can be moved in longitudinal
direction in order to prevent the workpiece from
becoming jammed.
Rule of thumb: The rear end of the stop comes
up against an imaginary line that begins roughly
at the center of the saw blade and runs at an
angle of 45° to the rear.
14:20 Uhr Seite 15
GB
15