Hercules FKS 2201 Mode D'emploi page 14

Anleitung FKS 2201_SPK7:Anleitung FKS 2200 SPK 7
GB
as to the need for additional precautions. Factors
with a potential influence on the actual immission
level at the workplace include the duration of impact,
the type of room, and other sources of noise etc.,
e.g. the number of machines and other neighboring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved.
5. Technical data
AC motor 230 V
Power P S1 1500 W S6 20% 2200 W
Idle speed n
0
Cutting-off wheel Ø 315 x Ø 30 x 3,6 mm
Number of teeth
Main Table size 800 x 350 mm
Sliding table dimensions 1000 x 300 mm
Sliding length max.
Cutting height max. 73 mm / 0°
49 mm / 45°
Height adjustment infinite 0 -73 mm
Tilting saw blade infinite 0° - 45°
Extractor socket
6. Before putting the machine into
operation
Unpack the bench-type circular saw and check it
for damage which may have occurred in transit.
The machine has to be set up where it can stand
firmly, e.g. on a work bench, or it must be bolted
to a strong base. The machine must stand
securely, i.e. the saw must be securely bolted to
the floor.
All covers and safety devices have to be
properly fitted before the machine is switched
on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machineʼs moving parts run smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
14
7. Assembly
Important! Pull out the power plug before
carrying out any maintenance, resetting or
assembly work on the cutting-off machine!
7.1. Setting up the saw (Fig. 1-9)
Place the saw with the table facing down on a
flat surface.
Fasten the four legs (18) to the machine body on
the inside, using four screws (SW13) for each
leg. When you insert the legs make sure that the
lugs of the legs fit the shape of the mounts
provided.
50Hz
Mount the four rubber feet (25) on the legs.
Fasten the chassis (15) to the legs on the inside,
2860 min -1
using two screws for each leg. In doing so, the 4
spacers (26) must be inserted between the legs
24
and the angle bracket (22) of the chassis. When
assembling, make sure that the rounded side of
the angle bracket faces the bottom of the
machine.
600 mm
Turn the saw upside down and place it on the
floor.
Carefully insert the sliding table (3) in the
slideways (24) and push to the point where the
locking hook (10) latches home.
Screw the mount for the extractor hose (29) and
Ø 100 mm
the tool hook (28) to the machine body (see Fig.
6 and 7).
7.2 Using the chassis (Fig. 11)
To swing the chassis out, gently lift the saw at
the back (a) and push the wheels backwards
(15) (b).
Then lower the saw again, keeping it in this
same position.
The saw is now standing on the wheels and be
transported by one person with the aid of the
handles (16). Important: Never lift the saw by
the sliding table.
Important: After transportation, the chassis (15)
must immediately be retracted in order to ensure
the saw is standing securely.
To do this, return the wheels to their starting
position by following the sequence in reverse.
7.3 Fitting / removing the saw blade guard (Fig. 9)
Mount the saw blade guard (2) on the splitter (5)
so that the screw fits through the hole (45) in the
splitter.
Do not tighten the screw (37) too far – the blade
guard must be able to move freely.
Fasten the extractor hose (13) to the extractor
adapter (16) and to the extractor socket of the
16.11.2006 14:20 Uhr Seite 14