Publicité
Lifting Considerations
Lifting Considerations
- Do not lift the unit when it is windy and while a personnel is working under the unit.
- Do not lift the unit when it is windy and while a personnel is working under the unit.
- Use lifting chain as shown below. Lifting chains must be capable of supporting the entire weight of the device.
- Use lifting chain as shown below. Lifting chains must be capable of supporting the entire weight of the device.
- Lifting chains may not be the same length. Set lifting chains to balance the device.
- Lifting chains may not be the same length. Set lifting chains to balance the device.
6.2 Levage
- If possible, create a parallel loop straps to the air flow direction.
- If possible, create a parallel loop straps to the air flow direction.
- For your safety, when unit is lifted up, you may use appropriate equipment method such as belts, straps.
- Ne levez pas la centrale en cas de vent et si des personnes travaillent en dessous.
- For your safety, when unit is lifted up, you may use appropriate equipment method such as belts, straps.
- Determine center of gravity of unit and test it by lifting up about 500 mm. If lifting point is not appropriate, re-determine it to prevent falls.
- Utilisez des élingues, comme indiqué ci-dessous. Elles doivent être capables de supporter le poids de l'appareil.
- Determine center of gravity of unit and test it by lifting up about 500 mm. If lifting point is not appropriate, re-determine it to prevent falls.
Not lifting the unit properly may cause serious injury even death.
- Si les élingues n'ont pas la même longueur, veillez à bien équilibrer l'appareil.
Not lifting the unit properly may cause serious injury even death.
- Si possible, les passants des sangles doivent être parallèles à la direction du flux d'air.
- Dans un souci de sécurité, pour lever la centrale, utilisez des équipements adaptés (courroies, sangles...).
Failure to follow the instructions above may cause damage of equipment, serious injury, or even death.
!
Failure to follow the instructions above may cause damage of equipment, serious injury, or even death.
!
- Identifiez le centre de gravité de la centrale, puis testez-le en soulevant la centrale d'environ 500 mm. Si le point de levage ne se trouve pas sur le centre
Subassemblies and parts of unit are equipped as shipped from the factory.
Subassemblies and parts of unit are equipped as shipped from the factory.
de gravité, corrigez-le pour éviter toute chute. La chute de la centrale peut entraîner des blessures graves, voire la mort.
Les sous-ensembles et composants de la centrale sont équipés en usine avant expédition.
For units that are dispatched as one
For units that are dispatched as one
piece, please place minimum 4 pipes
Pour les centrales monobloc, installez au
piece, please place minimum 4 pipes
into carrying holes which are located
minimum 4 taquets dans les orifices de
into carrying holes which are located
transport de la centrale et attachez-les au
on the unit and affix them to the
on the unit and affix them to the
dispositif de levage, puis
carrying handle then carry the units
transportez la centrale comme
carrying handle then carry the units
indiqué sur la Figure a.
as it is shown in figure a.
as it is shown in figure a.
Figure-a
Figure-a
Drain Connection
Drain Connection
1- If there is more than one drain pan, mount siphon to each individual section.
1- If there is more than one drain pan, mount siphon to each individual section.
2- Using only one siphon for all drainage connected to common line may cause overflow in the condensation pan.
2- Using only one siphon for all drainage connected to common line may cause overflow in the condensation pan.
3- Avoid applications prevent the flow of water in the drain line.
3- Avoid applications prevent the flow of water in the drain line.
4- Drain line should never be on higher level than the condensate pan.
4- Drain line should never be on higher level than the condensate pan.
12
12
VEX700T/H
For units that are dispatched as modular, please affix pipes
For units that are dispatched as modular, please affix pipes
into holes which are located on the units and carry with
Pour les centrales bi-blocs, installez les taquets dans les orifices de
into holes which are located on the units and carry with
ropes as it is shown in figure b.
transport de la centrale et attachez-les au dispositif de levage, puis
ropes as it is shown in figure b.
transportez la centrale comme indiqué sur la Figure b.
Figure-b
Figure-b
FR
11
Publicité
