Andis RBC Manuel D'utilisation page 6

MOUNTING AND DISMOUNTING THE BLADE SET
The blade set can be attached with the start switch in the "OFF" or "ON" position. When removing the
blade, turn the clipper off. Push the blade away from the clipper with your thumb, and the blade will pop
off (Diagram L). To replace or change the blade set, fit the black plastic tab on the blade set into the notch
located at the bottom of the clipper opening. Firmly push the blade onto the clipper housing, and it will
snap into place (Diagram M).
IMPORTANT: Frequently remove accumulated hair from the cavity under the blade set. Remove the blade
set as described above and brush hair from the cavity using a small brush or toothbrush.
USE GUIDELINES FOR CHARGER AND BATTERY PACK
1. The lithium-ion battery pack included with your clipper does not develop a "memory effect" like a
nickel-metal hydride (NiMH), or nickel cadmium (NiCd) battery. You can return the battery to the charger
at any time for a full charge, or even use the battery before a charge cycle is complete. Like most
rechargeable batteries, lithium-ion batteries perform best when used frequently.
2. For maximum battery life, store the lithium-ion battery pack in a partially discharged condition if the
unit will be unused for several months. To discharge the battery, run the clipper just until the blue light
turns off.
3. If the battery pack is left in the charger for several days without use, it is normal for the topmost of the
three white lights on the charger to repeatedly turn off and back on again. This is not a malfunction.
The charger will occasionally check the battery and maintain a full charge.
4. The charger works most effectively when battery packs are at, or close to, room temperature. A
lithium-ion battery pack returned to the charger unusually hot or cold may take more than an hour to
completely recharge.
5. Avoid locating the charger near heat vents, radiators, or in direct sunlight. Optimum charging will result
where the temperature is stable. Sudden increases in temperature can result in the battery pack receiving
less than a full charge.
6. Many factors influence lithium-ion battery pack life. A battery pack that has received heavy use or is
more than a year old may not give the same run-time performance as a new battery pack.
7. New lithium-ion battery packs, or packs unused for a period of time, may not accept a full charge. This is
normal and does not indicate a problem with the battery or charger. The battery will accept a full charge
after several cycles of clipper use and recharging.
8. Disconnect the charger from the AC outlet if extended periods of non-use are anticipated.
SAFETY RULES FOR CHARGER AND BATTERY PACK
1. Do not insert metallic objects into the battery pocket of the charger base (unless servicing your charger
as described under "User Maintenance–Care and Servicing of the Battery System").
2. Do not expose the charger to excessively dirty locations. If the storage or charger pockets become
clogged with dust or hair, unplug the charger and gently remove hair or other debris with a soft brush or
vacuum cleaner.
3. To clean external parts of the charger, use a soft brush or damp cloth. Do not use harsh abrasives,
detergents, or solvents.
4. Do not use the charger designed for this Andis clipper to attempt to charge any other battery.
5. The battery pack contains an overload protection feature. In extreme cases, overload protection may
cause the battery pack to become inoperable. Do not attempt to power any product other than the Andis
cordless clipper with this lithium-ion battery pack.
6. Do not allow the exposed metal contacts on the battery pack to make contact with any conductive
material (metal combs, scissors, paper clips, etc.).
7. For maximum battery life, do not store battery or charger under 50°F or over 104°F.
8. Do not expose the charger base or battery pack to excessively damp conditions.
9. Take care not to drop the charger base and the battery pack. Do not attempt to use a damaged battery
pack or charger.
6
https://manual-hub.com/