Descaling; Water Lter; Beverages Settings; Auto-O (Standby) - DeLonghi DINAMICA plus Mode D'emploi

• After cleaning, it is normal for the grounds container (A11)
to contain water.

6.4 Descaling

For instructions on descaling, see section "15.

6.5 Water lter

For instructions on how to install the lter (D4), see section "17.
Water softener lter".

6.6 Beverages settings

In this section, you can consult your customised settings and, if
you wish, reset the default values for each beverage and each
pro le.
1. Once in the settings menu, press "DRINK SETTINGS". The
values for the rst beverage appear on the display;
2. The values are displayed on vertical bars. The default value
is indicated by the
highlighted by the solid part of the vertical bar;
3. To go back to the settings menu, press
scroll and display the beverages, press
4. To reset the default values for the beverage displayed,
press ;
5. "CONFIRM RESET?": to con rm, press
cancel, press
6. "DEFAULT VALUES""SET": press
The beverage has been reset to the default values. Proceed with
the other beverages or go back to the homepage by pressing
twice.
Please note:
To change the beverages in another pro le, go back to the
homepage, select the required pro le and repeat the procedure.

6.7 Auto-o (standby)

Auto-o can be set so that the machine goes o after 15 or 30
minutes, or 1, 2 or 3 hours.
To programme Auto-o , proceed as follows:
1. Press "AUTO-OFF";
2. Select the required time interval by pressing the selection
arrows (increase) or
3. To con rm, press
Auto-o is programmed.
6.8

Energy saving

Use this function to enable or disable energy saving. When en-
abled, the function reduces energy consumption in compliance
with European regulations.
To disable or enable "Energy Saving", proceed as follows:
Descaling".
symbol, while the current value is
);
.
(decrease);
.
1. Press "ENERGY SAVING" to disable (
ble ( ) the function;
The corresponding symbol (B2) appears on the top bar of the
homepage to indicate that the function has been enabled.
Please note:
If "Energy Saving" is active, you may have to wait a few seconds
before delivery.

6.9 Co ee temperature

To modify the temperature of the water used to make the co ee,
proceed as follows:
"COFFEE TEMPERATURE"
1. Press
appear on the display (B1) (the current value is underlined);
2. Press the value you want to set (LOW, MEDIUM, HIGH,
MAXIMUM).

6.10 Water hardness

For instructions on setting water hardness, see section "16.
. To
Setting water hardness".
;

6.11 Set language

To modify the language of the display, proceed as follows:
"
1. Press SET LANGUAGE";
(to
2. Press the ag corresponding to the language you want
to set (press
available).

6.12 Beep

This enables or disables the beep emitted by the machine each
time an icon is pressed or an accessory is inserted/removed. To
disable or enable the beep, proceed as follows:
1. Press "BEEP" to disable (
function;

6.13 Bluetooth

This function enables or disables the protection PIN to connect
to the machine from a device.
1. Press "BLUETOOTH". The serial number of the machine (19
digits) and a 4 digit number (PIN) appear on the display (B1);
2. Press (
the PIN when you connect via the App;
The preset PIN is "0000". You are recommended to customise the
PIN directly from the APP.
Please note:
The serial number of the machine, visible in the "Bluetooth"
function, enables it to be identi ed unambiguously when an
association is created with the APP.
9
. The selectable values
to display all the languages
) or enable (
) to enable or ( ) to disable the request for
) or ena-
) the