Black & Decker MATRIX BDCDMT112 Manuel D'instructions page 7

• DONOT
splash or immerse in water or other liquids. This may cause premature ceflfailure.
• Do not store or use .the tool and battery pack in locations where the temperature may
reach or exceed 105 F (40°C) (such as outside sheds or metal buildings in summer).
z_WARNING:
Never attempt to open the battery pack for any reason. If battery pack case is
cracked or damaged, do not insert into charger. Do not crush, drop or damage battery pack.
Do not use a battery pack or charger that has received a sharp blow, been d-rop_ped, run over or
damaged in any way (i.e._ piercedwith a nail, hit with a hammer, stepped on). Damaged battery
packs should be returned to service center for recycfing.
z_WARNING:
Fire hazard. Do not store or carry battery so that metal objects can contact
exposed battery terminals. For example, do not place battery in aprons, pockets, tool boxes,
product k# boxes, drawers, etc., with loose nails, screws, keys, etc. Transportinq batteries can
possibly cause fires if the battery terminals inadvertenUy come in contact w_h conductive
materials such as keys, coins, hand tools and the like. The US Department of Transportation
Hazardous Material Regulations (HMR) actually prohibit transporting batteries in commerce or on
airplanes (i.e., packed in sufcases and carry-on luggage) UNLESS _heyare properly protected
from short circuits. So when transporting indiv/dqafSatteries, make sure that the battery terminals
are protected and well insulated from materials that could contact them and cause a short circuit.
NOTE: Lithium-ion batteries should not be put in checked baggage.
STORAGE RECOMMENDATIONS
. The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold.
• Long storage win not harm the battery pack or charger.
12VOLT MAX* BATTERY PACK (BDCDIViT112) CHARGING, iNSTALLiNG,
AND REMOVING
12VOLT MAX* CHARGING PROCEDURE
Black & Decker chargers are designed to charge Black & Decker
battery packs in 3-5 hours depending on the pack being charged.
1. Plug the charger (1) into an appropriate outlet before inserting the
battery pack (2).
2. Insert the battery pack into the charger. (Figure A)
3. The green LED will flash indicating that the battery pack is being
charged.
4. The completion of charge is indicated by the green LED remaining
on continuously. The battery pack is fully charged and may be used at
this time or left on the charger•
Recharge discharged batteries as soon as possible after use or battery life may
be greatly diminished. For longest battery life, do not discharge batteries fully. It is
recommended that the batteries be recharged after each use.
IMPORTANT CHARGING NOTES
1. Longest life and best performance can be obtained Jfthe battery pack is charged when the
air temperature is between 65°F and 75°F (18 °- 24°C). DO NOT charge the battery pack in an
air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is important and will
prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to touch while charging. This is a normal condition,
and does not indicate a problem. To facilitate the cooling of the battery pack after use, avoid placing the
charger or battery pack in a warm environment such as in a metal shed, or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check current at receptacle by plugging in a lamp or other appliance.
b. Check to see if receptacle is connected to a light switch which turns power off when you
turn out the lights.
c. Move charger and battery pack to a location where the surrounding air temperature is
approximately 65°F - 75°F (18 °- 24°C).
d. If charging problems persist, take the tool, battery pack and charger to your local
service center.