Publicité
Les langues disponibles
Les langues disponibles
13. Cleaning and maintenance
WARNING! Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
Cleaning
Keep all safety devices, air vents and the motor hous-
ing free of dirt and dust as far as possible. Wipe the
equipment with a clean cloth or blow it with com-
pressed air at low pressure.
We recommend that you clean the device immediately
each time you have 昀椀nished using it.
Maintenance
There are no parts inside the equipment which require
additional maintenance.
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consuma-
bles.
Wear parts*: Bandsaw blade, Table insert, Push stick
* Not necessarily included in the scope of delivery!
14. Storage
Store the device and its accessories in a dark, dry and
frost-proof place that is inaccessible to children. The
optimum storage temperature is between 5 and 30˚C.
Store the power tool in original packaging.
Cover the electrical tool in order to protect it from dust
and moisture.
Store the operating manual with the electrical tool.
15. Electrical Connection
The installed electric motor is connected and is ready
to work. The connection complies with the relevant
VDE and DIN regulations. The customer-side mains
supply and the used extension line must meet these
regulations.
Important information
In the event of an overloading the motor will switch
itself o昀昀. After a cool-down period (time varies) the
motor can be switched back on again.
Defective Electric Connection Lines
Often, insulation damages occur on electrical connec-
tion lines.
Causes are:
• Drag marks if connection lines are led through win-
dow or door clearances.
• Kinks due to improper attachment or routing of the
connection line.
• Cuts caused by running over the connection line.
• Insulation damages caused by pulling the connec-
tion line out of the wall socket.
• Fissures caused by the ageing of the insulation.
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
Such defective electric connection lines must not be
used and are hazardous due to the insulation damages.
Regularly check the electrical connection lines for dam-
ages. Please make sure that the connection lines are
disconnected from the mains supply during the check.
Electrical connection lines must comply with the rel-
evant VDE and DIN regulations. Only use connection
lines labelled with H05VV-F.
The labelling of the connection cable with the type
speci昀椀cation is required.
AC motor
• The mains voltage must be 230 - 240 V ~
• Extension cables up to 25 m long must have a cross-
section of 1.5 mm
2
.
Connections and repairs of electrical equipment may
only be carried out by an electrician.
Please provide the following information in the
event of any enquiries:
• Type of current for the motor
• Machine data - type plate
• Motor data - type plate
16. Disposal and recycling
Disposing of transport packaging
The packaging protects the machine from damage dur-
ing transport. The packaging material is usually chosen
for factors of environmental friendliness and disposal. It
can therefore be recycled. Returning the packaging to
the material life cycle saves raw material and reduces
waste.
Packaging parts (e.g. plastic sheets, Styropor®) can be
dangerous for children. Risk of choking! Store packag-
ing parts beyond the reach of children and dispose of
them as soon as possible.
Old devices must not be disposed of with house-
hold waste!
This symbol indicates that this product must not
be disposed of together with domestic waste in
compliance with the Directive (2012/19/EU) per-
taining to waste electrical and electronic equip-
ment (WEEE). This product must be disposed of at a
designated collection point.
This can occur, for example, by handing it in at an au-
thorised collecting point for the recycling of waste elec-
trical and electronic equipment. Improper handling of
waste equipment may have negative consequences for
the environment and human health due to potentially
hazardous substances that are often contained in elec-
trical and electronic equipment. By properly disposing
of this product, you are also contributing to the e昀昀ective
use of natural resources. You can obtain information on
collection points for waste equipment from your munici-
pal administration, public waste disposal authority, an
authorised body for the disposal of waste electrical and
electronic equipment or your waste disposal company.
GB | 31
Publicité
