TEFAL KO851 Mode D'emploi page 7

• Be sure to manipulate only the handle during heating until
completely cool.
• Your appliance is intended for domestic use inside the home only
at an altitude below 4000 m.
• The preselected temperatures are given for a product use below an altitude of 4000 m. Above
this altitude, the maximum temperature displayed at end of cycle on the product will be the
boiling temperature matching with the altitude of use.
• For your safety, this appliance meets applicable standards and regulations (Directives on Low
Voltage, Electromagnetic Compatibility, Materials in contact with food articles, Environment, etc.).
• Only plug the appliance into an earthed mains outlet. Check that the voltage indicated on the
rating plate of the appliance corresponds to that of your electrical installation.
• Any connection error will invalidate your guarantee.
• The guarantee does not cover kettles that fail to operate or operate badly due to a failure to
descale the appliance regularly.
• Do not let the power cord hang where children may reach it.
• Never disconnect the plug by pulling on the power cord.
• Any intervention other than normal cleaning and maintenance by the customer must be
performed by an Approved Service Centre.
• All appliances are subject to strict quality control procedures. These include actual usage tests
on randomly selected appliances, which would explain any traces of use.
• Never use scouring pads for cleaning purposes.
• To remove the scale filter, remove the kettle from its base and leave it to cool down. Do not
remove the filter when the appliance is filled with hot water.*
• Do not use any method to descale the kettle other than that recommended.
• Keep the kettle and its power cord away from any source of heat, from any wet or slippery
surface and away from sharp edges.
• Never use the appliance in a bathroom or close to a water source.
• Never use the kettle when your hands or feet are wet.
• Always unplug the power cord immediately if you observe any anomaly during operation.
• Never pull on the power cord to remove it from the wall socket.
• Always remain vigilant when the appliance is on, and in particular be careful of the steam
coming out of the spout which is very hot.
• Never leave the power cord hanging from a table top or kitchen counter to avoid any danger of
it falling to the floor.
• Never touch the filter* or the lid when the water is boiling.
• Also be careful as the body of stainless steel kettles becomes very hot during operation. Only
touch the handle of the kettle.
• Never move the kettle when it is in operation.
• Protect the appliance from damp and freezing conditions.
• Always use the filter* during heating cycles.
• Never heat the kettle when it is empty.
• Place the kettle and its power cord on a stable, heat proof and water resistant surface.
• The guarantee covers manufacturing defects and domestic use only. Any breakage or damage
resulting from a failure to comply with these instructions for use is not covered by the guarantee.
* : depending on model
BEFORE USING FOR THE FIRST TIME
1. Remove all of the various packaging, stickers or accessories from both the inside and outside of
the kettle.
2. Adjust the length of the cord by winding it under the base. Wedge the cord into the notch.
Throw away the water from the first two/three uses as it may contain dust. Rinse the kettle.
10
USE
1. TO OPEN THE LID, ACCORDING TO THE MODEL
– Press on the locking system and the lid lifts automatically.
To close, press down firmly on the lid.
2. PLACE THE BASE ON A FLAT, STABLE, HEAT-RESISTANT SURFACE AWAY FROM WATER
SPLASHES AND ANY SOURCES OF HEAT.
• Kettle is only to be used with the base provided.
3. FILL THE KETTLE WITH THE DESIRED AMOUNT OF WATER.
• Never fill the kettle when it is on its base.
• Do not fill it above the maximum level, or below the minimum level. If the kettle is too full,
boiling water may spill out.
• Do not use without water.
• Check that the lid is closed properly before use.
4. POSITION THE KETTLE ON ITS BASE. PLUG IT INTO THE MAINS SOCKET.
5. TO START THE KETTLE
When the kettle is placed on the base, all the lights illuminate. The water temperature in the kettle
is displayed on-screen.
TO HEAT WATER:
2 options:
– If you wish to start a boil cycle, press the
100°C appears directly on the screen, the kettle beeps and starts heating the water.
The kettle beeps twice once water temperature reaches 100°C.
• If you wish to select the temperature – 5 possible settings: 40°C – 70°C – 80°C – 90°C – 100°C –
press the key until it displays the temperature you wish to select. The selected temperature
blinks twice, then stays still. The kettle beeps and the kettle starts heating the water.
You can monitor the live temperature of the water on the screen.
Once the selected temperature is reached, the kettle beeps twice and stops heating.
KEEP WARM MODE
You can use the keep warm mode to keep the water at a selected temperature during 30 minutes.
Once the temperature has been selected, a long push on
The logo appears at the top of the screen.
You can also start the keep warm mode once the temperature has been reached. Do a long push
on the key. The logo
If you wish to turn off the keep warm mode, just press the
PLEASE NOTE
The long push will activate the keep warm only if you push the button less than 25 seconds after
the end of the boiling cycle, otherwise the screen will switch off.
PLEASE NOTE
The screen automatically switches off after 25 seconds – unless you have selected the keep warm
mode – but pressing any key will turn the screen on again anytime.
If you select 100°C and activate the keep warm function, the kettle keeps the temperature at 95°C
for 30mins.
If the temperature of the water in the kettle is higher than the temperature you select when
pressing , the heating won't start.
For instance, if the water temperature is 90°C, you won't be able to launch the heating by
(fig 1)
selecting 40°C, 70°C or 80°C.
(fig 2)
(fig 3)
button
will activate the keep warm mode.
will appear at the top of the screen.
key.
11
EN