Publicité
Les langues disponibles
Les langues disponibles
Step 3: Enter the Landxcape
TM
APP, and then follow the instructions to
connect to your Wi-Fi.
*The Serial No. can be found at the rear of Landxcape
Fig. G)
NOTE:
1. If your Wi-Fi information changes, Landxcape
according to Step 3.
TM
2. When Landxcape
is located in an area with low or no Wi-Fi
signal, instructions sent from the mobile App may not be executed
TM
immediately. Landxcape
will receive instructions when it returns
to an area with good Wi-Fi signal.
3. For strong Wi-Fi signal to ensure stable connection, it is
recommended to install Wi-Fi extenders to cover areas with weak
or no Wi-Fi signal.
6. Boundary Wire Basics
6.1. Pegging the Boundary Wire
Use the boundary wire distance gauge to set the correct distance
between the wire and the border of your lawn (more than 26cm).This
is the recommended distance. The provided distance gauge ensures
proper installation.
If your neighbor also uses a Landxcape
metre between your boundary wire and your neighbor's.
The boundary wire must outline the intended mowing area
exactly. Your Landxcape
TM
will become confused by extra bends or
coils of boundary wire that are not part of its mowing area (See Fig.
H). If there is excess boundary wire after the mowing area has been
outlined, cut it off and store this additional wire in a separate location.
It is important to leave the necessary length where it connects to the
charging base so it can be connected and still remain buried.
6.2 Burying the Boundary Wire
If you are planning to bury the boundary wire, it is recommended to first
peg it down. This allows you to easily change the layout if necessary before
burying the wire. When the boundary wire installation is complete, have
TM
Landxcape
follow and check the path by pressing
TM
allows your Landxcape
to adjust to its new environment. .
TM
While observing Landxcape
you can easily make alterations to the
boundary wire to ensure Landxcape
the charging station. Confirm that Landxcape
station successfully, and bury the wire if desired.
6.3 Joining the boundary wire
If you want to extend and splice the boundary wire, use a connector.
(only for specific model, please check Technical Data & Declaration
of Conformity).The connector is waterproof and provides optimal
connection.
Insert both wire ends in any two of the three holes of the connector.
Insert the wires fully until both wire ends are visible on the other side of
EN
TM
as shown. (See
TM
needs to be re-set
TM
, keep a spacing of at least 1
and
. This
TM
's trouble-free tracking when locating
TM
docks in the charging
the connector. (See Fig. I) Press the connector together by using a pair
of pliers. (See Fig. J1, J2)
WARNING! It is not recommended to simply splice the boundary
wire with insulating tape or use a screw terminal block for
connection. A broken circuit may occur after a period of time as soil
moisture can oxidize the wire.
7. Software update
The software can be updated when new versions become available.
The latest software can be downloaded from our website
www.landxcape-robotics.com.
Method 1: Update via USB. See below for download and installation
instructions:
(1) Locate the latest software version at: www.landxcape-robotics.
com. Save the file to an empty FAT32 formatted USB (flash drive).
Delete any other files on the drive and check the format. If the drive
is not formatted in FAT32 , please reformat the drive.
NOTE: the software update is downloaded as a zipped file. You will
need to unzip or extract it before proceeding.
TM
(2) Place Landxcape
on a secure and level surface. Press
TM
off your Landxcape
.
(3) Insert the USB drive (flash drive) in the port. (See Fig. K1)
TM
(4) Turn Landxcape
on. The update will begin automatically. Wait until
the display shows "
" (See Fig. K2), then remove the USB drive
(flash drive) and tightly close the protective cover. When the display
shows "
", the update is complete and Landxcape
the PIN page.
Method 2: Update via your smartphone. (Only for specific model,
please check Technical Data & Declaration of Conformity)
TM
If your Landxcape
is connected to your smartphone via the
TM
Landxcape
App, you can check the software version.
The manual included with your Landxcape
software at the time of production. Some new features/functions in the
new version may not exist in the manual. If you found some settings not
in the manual, please visit www.landxcape-robotics.com to download
the latest manual.
8. Maintenance
TM
Your Landxcape
works hard and needs to be cleaned and checked
from time to time. Some parts will require replacement as they become
TM
worn. Never use your Landxcape
Switch off the machine before carrying out any service or maintenance.
Here's how to take care of your Landxcape
8.1 Keep it sharp
WARNING: Before cleaning, adjusting, or replacing the
blades, turn your Landxcape
gloves.
WARNING: When fitting new blades, make sure you
replace ALL the blades. Always use new screws when
fitting blades. This is important to ensure blade retention and
balance the blade turning disc. Failure to use new screws could
cause serious injury.
TM
Landxcape
does not cut grass like other mowers. Its cutting blades
are razor sharp on 2 edges and rotate in both directions for maximum
cutting capacity (See Fig. L). Each blade of your Landxcape
to turn
TM
will enter
TM
is based on the default
with defective main switch.
TM
.
TM
OFF and put on protective
TM
has 2
17
Publicité
