Table des Matières
Publicité
Operating instruction for electric fence controller hotSHOCK A50
en
with GPS SECURITY and SMS CONTROL
in connection with safety hints SECURA ANIMAL or SECURA SECURITY
(www.horizont.com)
Installation and connection:
The controller can be mounted alternatively onto a wall or a solid post. The earth stake must
be inserted into the ground as far as possible at a moisty place and must be connected to
the earth terminal
(
) of the controller by means of a noncorrosive wire.
Connect the fence connecting lead to the fence terminal (
The controller is water protected only when being installed acc. the instructions. Prodect
from bright sunshine. Do not operate the energizer when laying on the ground.
Operation (see fig. 2)
Connect the controller to a 12V wet battery ( red + / black - ), ensure that the terminals are
absolutely clean and the polarity is correct.
Use only rechargeable 12V- lead-acid batteries, during charging lead-acid batteries must be
placed in a well-ventilated area.
Press the switch (1)
The battery indicator light (2) „accu-test" is
permanent green
= battery is fully charged
no light or flashing green
= battery must be charged
After a few seconds a slight tic-tac can be heard. The control lamp (3) flashes with the
pulses. In case of wrong polarity the controller will not operate. If the control lamp (3) flashes
with the the pulses energizer operates properly. If this lamp is not or steady illuminated the
energizer is faulty.
fig. 2:
The energizer has two fence terminals
(Z1) = max output
(Z2) = reduced output
Both outlets can operate separate fences at the same time. A short in the Z2 fence has
no strong influence on Z1 but a short or a deviation in Z1 means a further reduction of Z2.
Grounding:
For a faultless operation and to obtain best possible output a good grounding is very im-
portant. There fore the grounding must be made at a rather moisty and overgrown place.
An 1 m earth stake ( e.g. 12mm ø ) shall be used. With long fences and on dry soil a ground
return wire with intermediate groundings (every 50 m) is necessary. (fig. 4)
Service:
Servicing is only to be made by qualified service personell.
Only by the manufacturer commanded replacement parts must be used.
8
or
) - fig. 3
Operating instructions for GPS SECURITY and SMS CONTROL:
Installation and connection:
The additional device GPS SECURITY and SMS CONTROL device are built in operable in the electric fencer. Please
let your SIM card unlock with the help of the enclosed documents.
Activate the SIM card at the provider.
See website Congstar: https://www.congstar.de/prepaid/sim-karte-freischalten
Unlocking the SIM card should take place within 24h.
The auxiliary module is accessible after about 5 minutes and the backup battery in the auxiliary module is loaded.
No user profiles are active during the first commissioning so that the auxiliary module can be accessed freely by each
mobile telephone.
Operation of the additional device GPS SECURITY and SMS CONTROL:
Please connect the electric fencer with the 12 V battery The additional module is available after 2 minutes approxi-
mately.
Status check by calling the additional device and status advise for status information via SMS:
Please call to the additional device from a cell phone. The call will be interrupted after 2 call signs.
You will get an SMS from the additional device with following information, which
you will get with each status update:
http://maps.google.com/maps?f=q&hl=en&q=.........
You can enter the coordinates by yourself in google-maps and query the loca-
tion. The link can be opened immediately from your mobile phone (Smartphone) in
google-maps. The location of the electric fencer will be shown.
loc: 51.286368,8.857165 ..........Location coordinates of the electric fencer
&speed: 0.00 ............................Current speed of additional device over ground
01/01/13 11:55 .........................Date and time of the last allocated location
F:4,32V ....................................current voltage of backup battery of the additional
module
M:12,0V ...................................Current voltage of the 12 V main power source*
Signal: F oder L .........................F means that the GPS signal suffice for the esta-
blishment. L means that the GPS signal is insuffici-
ent for the establishment.
Imei:012896000578432 ............Device identification number
* Voltages above 12 volts are shown as 12V (and not
as 13,6 volts for example). The voltage value can fluctuate at +/- 0,4 volts around the
shown value.
Alert message:
You will get following alert messages from the device if the voltage limits are reached or the location of the electric
fencer has changed:
Signal:F low voltage .................The voltage of the 12 V main power source has fallen to 11,4 Volt or less
Signal:F Low batt ......................The voltage of the internal backup battery ensures operation of the additional device
for a few more minutes. During this time, the additional device can't communicate with
you, until the electric fencer is again connected to the power source.
Signal:F moved .........................The electric fencer has been disconnected from it`s referred location.Location and
movement functions:
Send a SMS to the additional device with following content:
The given answer of the additional device will be:
The additional device will memorize the location. If the fencer is moved more than 300 m from the allocated location,
the mobile phone which was sending "move300", will get a SMS again.
Content of the SMS will be:
Send a SMS to the additional device with following content:
The given answer of the additional device will be:
The additional device will not memorize the location. Relocation will not be reported in the future.
Advise: Before you register your fencer in a new location you have to cancel the previous location with nomove.
additional device:
http://maps.google.com/
mapsßf=q&hl=en&q=loc
: 51.286368,8.857165 &sp
eed: 0.00 01/01/13 11:55
F:4,32V Signal:F Imei:
012896000578432
move300
move ok
Signal:F moved
nomove
nomove ok
9
Publicité
Table des Matières
