Eurosystems M250 EVO Manuel D'instructions page 10

12. Always turn off the pump immediately after each use / pause even though it is in stand-by
mode to optimize battery life.
13. At the end of spraying is necessary to flush the system by inserting clean water in the tank
and emptied by operating the pump with the taps open. (Fig. B) To clean the filter (2) unscrew
the transparent cover (3) and rinse it thoroughly.
14. NEVER discharge any product residues into the environment cas it can be a source of
pollution. Collect them in a box and dispose them in accordance with the legislation in force or
by following the manufacturer's instructions.
15. Any improper use, repairs carried out by unskilled/unspecialized personnel or the use of
non-original parts, leads to the decay of the warranty and decline all responsibilities from the
Manufacturer.
FIRST BATTERIES RE-CHARGE
ATTENTION : (Fig. C) in order to make the recharge it is NOT necessary to take the batteries out from
the containers (4). (Fig. D) Connect terminal (5) of the battery cable (6) to the terminal of the battery
charger and then connect the battery charger to the electric power 230 V socket. Leave it on charge until
the LED present on the battery switch off. The switched off LED is showing the batteries are completely
charged. The recharge cycle can last up to 10 hours.
Attention : it is possible to leave the battery charger pad connected even after the LED light switch off
at the end of the recharge. The battery charger will automatically switch off and switch on in order to
maintain the best and more constant batteries charging level. In order to use the machine disconnect
the battery charger out from the power outlet 230V. Disconnect the connector (5) of the cable from the
connector (6) of the battery charger by exerting a push (Fig. E) from the bottom upwards with the thumb
on the locking tab.
MOUNTING:
The ECO SPRAYER is delivered to destination, unless otherwise agreed, partially
disassembled and placed into its packaging. To make the machine operating, user should complete the
assembly of the disassembled parts, with the following procedure: remove the components from the
packaging.
Fig. F-G) Remove the nut and washer from the support wheel (7), slide it and reinsert it from below, in
bushings (8) of the frame. Insert the washer (9) and tighten the nut (10) with the key 24, without blocking
rotation of the support. Perform the same procedure for the other wheel.
(Fig. H) Tighten the support tube (15) to the plate (16) with 4 screws (17) and No. 4 nuts (18).
(Fig. I) Attach the nozzle (19) to the rubber tube (20) wound around the support.
ELECTRICAL CABLES ASSEMBLY FOR PUMP:
(Fig. K) Insert the power cord from the bottom pump (21) into the tube (22) until it comes out of the hole
to switch (Fig. L - part. 23). Connect the two Faston cables (24) to switch tabs (25).
(Fig. M) Place the switch into the seat (23) on the tube until it locks. (Fig. A - Part. 1) Connect the male
connector of the pump cable to the female connector of the batteries cable.
Check the correct connecting the cables , "turning on" the pump with the switch in position. "1": you
should feel the "buzz" of the pump. Turn off bringing the switch to pos. "0".
Attention ! For a correct use of the batteries do not extend the pump working when the batteries
are discharged.
ASSEMBLY ATTACHMENT MACHINE:
(Fig. N-O) With the machine with the engine off and in horizontal position, engage the pin (26) in the seat
of the quick connector (27). Then insert the spacer (28) and lock the pin with the safety pin (29).
SPRAYING OPERATION :
Place the liquid in the tank and before putting the pump into operation, choose the most suitable type
of application:
A. With front nozzle: to distribute liquid for snow –melting or herbicide on the ground.
B. With spear: for watering or spraying in hard to reach areas, or to perform biological treatment plants
or plant protection to orchards, hedges and olive groves areas, etc.
EN 11