Publicité
Les langues disponibles
Les langues disponibles
SAFETY INSTRUCTIONS
Read all safety warnings and instructions
that were provided with the drill stand or
the drill. Failure to follow the safety warn-
ings and the instructions may result in
electric shock, fi re and/or serious injury.
Save all safety warnings and instructions for future
reference.
•
Prevent dripping, leaking or unintentional uncoupling
of water hoses. Pay attention to the cooling water
during drilling overhead. Remove cooling water in a
safe way, for instance with a vacuum-cleaner. Keep
electric cables, plugs etc. dry.
•
Watch what you are doing. Use common sense. Do
not operate machinery when you are tired or not con-
centrated. Make sure that you can always stop the
motor (emergency stop). Do not use the machinery
of which the ON/OFF switch does not work properly.
•
Do not wear loose clothing or jewellery. They can
be caught in moving parts. When working in open
air rubber gloves and non-skid footwear are recom-
mended. Wear protective hair covering to contain
long hair.
•
Wear a helmet against falling parts, gloves for pro-
tection against sharp items and a safety goggle for
protection against sparks/small concrete particles.
Use a dust mask covering mouth and nose if nec-
essary. Ear protectors are recommended for sound
levels over 80 dB(A). For sound levels over 90 dB(A)
ear protectors are compulsory.
•
Disconnect the plug from the power source before
making any adjustments or changing accessories.
Starting drills accidentally is the cause of some ac-
cidents.
•
Do not overload the drill rig and do not use it as a lad-
der or scaffold. Overloading or standing on the drill
rig can raise the drill rig's centre of gravity and cause
it to tip over.
•
Keep machinery tools sharp and clean for better and
safer performance. Follow maintenance instructions.
Keep handles dry and free from oil and grease.
•
Check for alignment and binding of moving parts.
Breakage of parts and any other conditions that may
affect the normal use of the machinery. A guard or
parts that are damaged should be properly repaired
or replaced by an authorised service centre.
•
The use of accessory and attachment other than
recommended in this manual or the catalogue may
present a risk of physical injury.
•
Have your drill stand serviced/repaired only by a
qualifi ed repair person using original replacement
parts. This will ensure that the safety of the device
is maintained.
•
Cluttered areas invite injuries. Do not let uninvited
persons or animals contact machinery or enter the
work area. Make provisions to catch loose concrete
parts/cooling water when drilling in storey fl oors or
roofs. When not in use, machinery must be stored in
a dry, locked-up place, out of the reach of children.
•
Keep work area clean. Pay attention to all cables
20
ENGLISH
(underground!), pipes and steel reinforcement in the
work area. Do not use electric power tools in the pre-
sence of infl ammable liquids/gases or in humid (rain)
conditions.
•
Mount accessories and tools in the right way to pre-
vent them from coming loose. Check if all keys and
adjusting wrenches are removed from the machinery
before turning it on. Keep proper footing and balance
at all times.
WARNING! Under no circumstances may
the design of the machine be modifi ed wit-
hout the permission of the manufacturer.
Always use genuine accessories. Non-aut-
horized modifi cations and/or accessories
can result in serious personal injury or the death of the
operator or others.
MAIN COMPONENTS
The numbering of the illustrated product features refers to
the representation of the drill stand on page 4
1.
Column
2.
Lever
3.
Handle
4.
Carriage
5.
Vacuumblock
6.
Levelling screw
7.
Base
8.
Vacuumrubber
9.
Drill-hole centre indicator
SPECIFIED CONDITIONS OF USE
The core drill rig is one out of a series of lightweight machi-
nes meant for drilling with diamond core drilling bits. The
machine can be used for drilling in concrete, asphalt en
stone-like materials. The function of the drill rig is to posi-
tion and guide the drill motor during the drilling process.
WARNING! If the vacuum plate is used,
make sure the support surface is not po-
rous and can loosen from the fl oor or the
wall. Make sure that the vacuum pump has
suffi cient power to secure the vacuum pla-
te. The vacuum plate must never be used for ceiling dril-
ling. Careless or incorrect use can result in serious,
even fatal injury.
Do not use this product in any other way as stated for nor-
mal use.
NMH0160 • 05.04.2013
Publicité
