Kuppersbusch KI6880.1SR Mode D'emploi page 59

EN
also set the timer for times greater than
(11) for one second. A 2.0 (time in
on the Timer Indicator (12). Pressing
the sensor
the time will increase from 30 to 30
time is programmed. The maximum
programming time available is 9.5
hours.
Setting a timer on a plate.
Once the power level is set on the
be able to be timed.
To that end:
1 Touch sensor (10) or
Timer Indicator (12) will show "00"
and corresponding zone indicator
(3) will show the symbol
alternately with its current power level.
2 Immediately afterwards set a cooking
using the sensors (10) ó
will start at 01. By keeping sensors
(10) ó
will be restored to 00. When there is
will begin to count down in seconds.
3 . When the timer indicator (12) stops
the time automatically. The indicator
(3) relating to the timed hotplate
will alternately display the selected
power level and the symbol
Once the selected cooking time has
The timer indicator (12) will display a
(4) of the selected zone. If the heating
(3) will display alternately the H symbol
and a "-".
58
If you wish to time another hotplate
If one or more zones are already
show by default the shortest remaining
related zone. Rest of timed zones will
show on their corresponding indicator
zones the decimal dot blinking. When
cursor "slider" of another timed zone
remaining time of that zone for a few
seconds and its indicator will show its
power level and the "t" alternately.
Changing the programmed time.
"slider" (2) of timed zone has to be
pressed. Then it will be possible to read
and modify the time.
Through sensors
you can modify the programmed time.
(11).
Disconnecting the clock
If you wish to stop the clock before the
blinking
done at any time by simply adjusting
its value to '--'.
1 Select the desired plate.
(11).
2 Adjust the value of the clock to "00"
by using the sensor
clock is cancelled. This can also be
done more quickly by pushing the
"sensors
same time.
Power Management
Function
This model is equipped with a power
limiting function (Power Management).
This function allows the total power
generated by the hob to be set to
having connected the hob to the power
limiting menu.
1 Press the
seconds. The letter PL will appear on
the timer indicator (12)
2 Press the locking touch key
3
you must unplug the hob and plug it in
again after a few seconds. Thus you
will again be able to enter the power
limiting menu.
Every time the power level of a hotplate
calculate the total power the hob is
generating. If you have reached the total
allow you to increase the power level
of that hotplate. The hob will beep and
the power indicator (3) will blink at the
(10) and
level that cannot be exceeded. If you
lower the power of the other hotplates.
Sometimes it will not be enough to
lower another by a single level as this
depends on the power of each hotplate
and the level it is set at. It is possible
that to raise the level of a hotplate
that of several smaller ones must be
turned down.
If you use the quick switch-on at
maximum power function and the said
(10). The
the hotplate will be set to the maximum
possible level. The hob will beep and
(10) and (11) at the
the said power value will blink twice on
the indicator (3).
These functions have pre-allocated
obtaining excellent results as the
temperature of the pan is controlled
continuously by sensors. When the
target temperature for the function
maintained without needing to change
the power level.
The Chef functions operate correctly
(11) touch key for three
with pans with the same ferromagnetic
area on the base of the pan as the
for high temperature functions (above
(6).
the hob can be limited will appear
and these can be changed using the
(11) and (10) sensors.
once again press the locking touch
key (6). The hob will be limited
to the chosen power value.
Special functions: CHEF