IPC D 1814P4 T Manuel D'instructions page 26

USING COLD WATER
It is suitable for removing light dirt or for rinsing operations
on garden tools, walls, balconies, hard floors in general,etc.
Adjust water pressure according to your needs.
USING "ECO" MODE
In the "ECO" mode, the pressure washer uses temperature
up to 60°C, which offers an efficient use of resources with a
positive impact on the environment.
USING HOT WATER AND VAPOUR (If available)
For a correct use of the Hot Water and Vapour Mode (if avai-
lable), it's advisable to use the following temperatures:
- Light dirt: 30 - 50 °C:
- Proteic dirt, e.g., in the food sector: 60 °C Max
- Cleaning Automobile or Machine Tools: 60 - 90 °C
- Debinding, Persistent greasy dirt: 100 - 110°C
- Facade cleaning, Sanitization of surfaces: up to 110 °C
To use the Vapour mode, nozzel series A.P. must be sub-
stitute with the recommended vapour nozzle offered as
Optional accessory.
With working temperature more than 95°C (203°F), the pressu-
re that indicates on the manometer must be
(460 PSI).
!
Danger
During use with boiling water, "Steam Phase", keep away
from the openings for fumes discharge (risk of burning).
When you have finished using the "Hot Water or Steam
Phase", let the machine cool down for about 3 minutes
with the gun turned on.
STOPPING THE CLEANER
1) Switch off the burner by turning the pressure regulator to
pos. "0" (fig. 7B).
2) Let the cleaner run with cold water only for at least 30
seconds to cool down the boiler.
3) Stop the cleaner by turning the selector switch to pos. "0"
(fig. 7A).
4) Discharge the pressure from the H.P. hose by pressing the
trigger on the gun.
5) Disconnect the water cleaner from the mains electricity
supply via the Solenoid switch or by unplugging the plug from
the socket.
6) Turn off the water supply tap (fig. 5A).
English
!
Warning
- If the water cleaner is left, even temporarily, turn it off by using
the Solenoid switch or by unplugging the plug from the socket.
- Water cleaners with the "Total Stop" device should be con-
sidered as off when the Solenoid switch is in the "O" position
or the plug is unplugged from the socket.
- When the water cleaner is not used, close the safety device
on the handle.(fig. 10).
- Dry use of the water cleaner causes serious damage to
pump gaskets.
!
Warning
This cleaner has been designed for use with the detergents
supplied or recommended by the manufacturer.
The use of other detergents or chemicals may influence the
safety of the cleaner.
1) For environmental compatibility, we recommend a rea-
sonable use of detergents, according to the instructions on
the pack.
2) From the range of recommended products, choose the
one most suited to the washing job to be done and dilute it
with water according to the instructions on the pack or in the
catalogue of the detergents most suited for the type of hot or
cold water cleaner.
3) Ask your dealer for the detergents catalogue.
< a 32 bar
OPERATING PHASES FOR CORRECT CLEANING WITH
DETERGENTS.
1) Prepare the solution of detergent at the concentration most
suitable for the type of dirt and the surface that is to be washed.
2) Start the cleaner, activate the detergent suction control on
the lance (fig. 9) and spray the surface to be washed, working
from the bottom upwards.
Leave to work for a few minutes..
3) Rinse the whole surface well from top to bottom with hot or
cold water at high pressure.
4) After use with detergent, flush out the intake circuit; place
the detergent suction hose in a tank of clean water and let the
pump run for 1 minute with the dosing tap turned fully on and
the lance in detergent delivery condition.
24
ADVICE ON USING DETERGENTS